Dediprog Adapters
-
BBF Testclip (SO8W or SO8N)
Out of Stock - Order Now, Ships within 10 daysThe BBF SO8 Test Clip is used to connect the Backup Boot Flash Tool to the Main Serial Flash soldered on board offering the possibility to the application controller to work on the Backup Flash automatically without the need of connector.
The BBF SO8 Test Clip is frequently used in combination with the Backup Boot Flash Tool to develop Bios code or repair Desktop and notebook using Serial Flash.
- Compatible with most of the applications (no hardware modification needed)
- Compatible with SO8N (150mils) and SO8W (200 mils) package
-
Dediprog 2.54mm 2x10 To 1.27mm 2x10 Adaptor
Out of Stock - Order Now, Ships within 10 daysThe adaptor and cable are used with the Dediprog SF600 programmer to convert 2.54mm 2x10 female header to a1.27mm 2x10 female header.
-
Dediprog 200-AD-8N Programmer Adapter
The Dediprog 200-AD-8N adaptor is used with Dediprog SF200 programmer for serial flash with SO8W packages.
-
Dediprog 8-pin SOP8N SPI/EEPROM Adapter
SOP8N 8-Pin programming adapter for SPI and EEPROM devices.
-
Dediprog 8-Pin SOP8W SPI/EEPROM Programming Adapter
SOP8W 8-Pin programming adapter for SPI and EEPROM devices.
-
Dediprog BBF-CON-8 SO8 Connection Adaptor
Out of stockSO8 Connection Adaptor for BBF is used to connect Backup Boot flash module-SO8W Socket (2.54mm 2x5) to 1.27mm 2x4 pin header soldered on the application. In this way, the application can work (boot) from Backup Boot Flash Module-SO8W socket directly. Refer to the following Pin Configuration for SO8 connector on the SO8 Connection Adaptor.
-
Dediprog EM-AD-RF16-Kit Reference Flash Adaptor Kit
When using the EM100 and EM100Pro, you may want to use a real serial flash to verify the developed code. This can be done by unplugging the EM100 from the target board and plug the reference flash adaptor by using the same 1.27mm 2x8 cable. The reference flash adaptor is soldered with 1.27mm 2x8 male header, SO16W engineering socket, and 2.54mm 2x4 male header. The 1.27mm 2x8 male header is used to connect to the target board with the same male header soldered on the target board. The engineering socket is used to insert a real serial flash. The 2.54mm 2x4 male header can be used to connect to Dediprog SF100 ISP programmer with ISP cable to program the updated codes into the chip.
Note: During SF100 update the reference flash adaptor, reference flash adaptor cannot be connected to the target board.
-
Dediprog EM-AD-RF8W-Kit Reference Flash Adaptor Kit
When using the EM100 and EM100Pro, you may want to use a real serial flash to verify the developed code. This can be done by unplugging the EM100 from the target board and plug the reference flash adaptor by using the same 1.27mm 2x4 cable. The reference flash adaptor is soldered with 1.27mm 2x4 male header, SO8W engineering socket, and 2.54mm 2x4 male header. The 1.27mm 2x4 male header is used to connect to the target board with the same male header soldered on the target board. The engineering socket is used to insert a real serial flash. The 2.54mm 2x4 male header can be used to connect to Dediprog SF100 ISP programmer with ISP cable to program the updated codes into the chip.
Note: During SF100 update the reference flash adaptor, the reference flash adaptor cannot be connected to the target board.
-
Dediprog EM-PRO-CON-SO8 SO8 1.27mm 2x4 Adaptor
Out of stockSO8 Connection Adaptor for EM100Pro-G2 or EM100Pro is used to connect EM100Pro-G2 or EM100Pro (2.54mm 2x10) to 1.27mm pin header soldered on the application. In this way, the application can work (boot) from EM100Pro-G2 or EM100Pro directly. Refer to the following pin configuration for SO8 connector on the SO8 Connection Adaptor.
SO8 Connector Pin Out
-
DediProg Intel ISP Adaptor A
The Intel ISP Adaptor A is only used to connect SF100 to Intel Motherboard.
Mated with Intel 2x10 connector (Samtec: ASP-159358-03).
The cable length is around 8 cm.
-
Dediprog ISP-ADP-127 SF100 Adaptor To 1.27mm 2x4 ISP Cable
ISP-ADP-127 Cable Adaptor is used to connect SF100 pinout (2.54mm 2x7) to 1.27mm pin header (SO8) soldered on the application.
SF100 1.27mm 2x4 Header Pin Out
1 Vcc GND 2 3 CS CLK 4 5 MISO MOSI 6 7 Vpp/Acc I/O3 8 -
Dediprog ISP-ADP-INTEL-A2 Intel ISP Adaptor A2
The Intel ISP Adaptor A2 is only used to connect SF100 to Intel Motherboard.
Mated with Intel 2x10 connector (Samtec: ASP-159358-03).
The cable length is around 8 cm; a header is added at the end.
-
Dediprog ISP-ADP-intel-B Intel ISP Adaptor-B
The Intel ISP Adaptor B is used to connect SF600/SF600Plus to Intel motherboard.
Mated with Intel 2x10 connector (Samtec: ASP-159358-03).
The cable length is around 8 cm.
Note: This adaptor does not work with Quad IO. Please choose“ISP-ADP-intel-C” for Quad IO.
-
Dediprog ISP-ADP-intel-B2 Intel ISP Adaptor-B2
The Intel ISP Adaptor B2 is used to connect SF600/SF600Plus to Intel motherboard.
Mated with Intel 2x10 connector (Samtec: ASP-159358-03).
The cable length is around 8 cm; a header is added at the end.
-
Dediprog ISP-ADP-intel-C Intel ISP Adaptor-C
The Intel ISP Adaptor C is for connecting EM100Pro, EM100Pro-G2, SF600, and SF600Plus to Intel motherboard.
Mated with Intel 2x10 connector (Samtec: ASP-159358-02 or TFM-110-02-S-D-A).
The cable length is around 8 cm.
Supports Quad IO.
-
Dediprog ISP-ADP-intel-C2 Intel ISP Adaptor
The Intel ISP Adaptor C2 is for connecting EM100Pro, EM100Pro-G2, SF600, and SF600Plus to Intel motherboard.
Mated with Intel 2x10 connector (Samtec: ASP-159358-02 or TFM-110-02-S-D-A).
The cable length is around 8 cm; a header is added at the end.
Supports Quad IO.