Audio and Voice Click Boards™

Products: 116 of 19
  • 2 x 20W Amp Click Board™

    The 2x20W Amp Click Board™ is a Stereo, 20W high-performance digital amplifier.

    The board is based on the MAX9744 stereo class D audio power amplifier from Maxim. This Click Board™ brings the Class AB sound performance with Class D efficiency. The perfect combination for your speakers. 2x20W Amp Click Board™ also offers 64 step volume control, single-supply operation, adjustable gain, and industry-leading Click Board™-and-pop suppression.


    .


    Not rated yet
    • $22.49
    • Including 20% UK VAT*
  • 2 x 30W Amp Click Board™

    The 2x30W Amp Click Board™ is a class-D audio amplifier with a tremendous output power, considering its size and lack of huge heatsinks, usually associated with the audio amplifiers. This is due to the fact that the efficiency of the amplifier IC is quite high (greater than 90%), featuring the efficiency boost mode, which dynamically reduces the current ripple of the external LC filter and current in idle mode. The integrated self-protection circuits include over-voltage, under-voltage, and over-temperature protection, output DC offset detection, as well as the short circuit detection, with the error reporting feature, via the dedicated pin.


    Not rated yet
    • $24.63
    • Including 20% UK VAT*
  • 2 x 5W Amp Click Board™

    The 2 x 5W Audio Amplifier Click Board™ functions as an amplifier and features the TDA7491LP 2x5-watt dual BTL class-D audio amplifier. The Click Board™ is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over the following pins on the MikroBUSline: AN, RST, CS, PWM, INT.

    The 2 x 5W AMP Click Board™ features a 3.5mm input jack and four output screw terminals for connecting passive speakers.

    Note: In order to achieve full 2x5W output power, keep in mind that you need to supply enough current to the chip. This is achievable with the EXT PWR header, but you need to switch over the AMP VCC to the left position.

    Not rated yet
    • $20.35
    • Including 20% UK VAT*
  • Audio XOver Click Board™

    The Audio Xover Click Board™  is an analog active crossover solution for two-way loudspeakers. The primary purpose of the crossover circuit in a loudspeaker is to split an incoming audio signal into frequency bands that are passed to the speaker or “driver” best suited. Audio Xover Click is based on Microchip’s MCP6H012 operational amplifier with rail-to-rail output operation, connected in configuration for 2nd order Butterworth filter for both low pass and high pass filters. With a frequency response independent of the dynamic changes in a driver's electrical characteristics and individual channel cutoff frequency selection it's great solution for crossover.

    Audio Xover Click board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $19.28
    • Including 20% UK VAT*
  • AudioAmp 2 Click Board™

    The Audio Amp 2 Click Board™ is a highly efficient class D audio amplifier, using the TDA7491, a dual BTL class-D audio amplifier IC, capable of delivering up to 20W to 8Ω load. This amplifier IC features high-efficiency output stage drivers and clever design, allowing it to deliver a reasonably high power to the connected speakers, using only GND polygon on the PCB for heat dissipation. In the BTL topology, the output DC blocking capacitors are not required. This allows for simpler design and lower power losses, especially with no input signal. The TDA7491 amplifier IC is equipped with a set of protection features, that allow reliable operation.

    Not rated yet
    • $22.49
    • Including 20% UK VAT*
  • AudioAmp 3 Click Board™

    The AudioAmp 3 Click Board™ is a stereo audio amplifier, capable of delivering up to 79W per channel with the 4Ω load. It is based on the TAS5414, a class-D integrated amplifier, which utilises a highly efficient switching scheme. Advanced EMI Suppression with Spread Spectrum Control allows using ferrite bead filters instead of bulky inductors, still maintaining the required EMC levels. The TAS5414 IC is equipped with a set of protection features, allowing a reliable operation.

    Not rated yet
    • $48.20
    • Including 20% UK VAT*
  • AudioAmp 4 Click Board™

    The AudioAmp 4 Click Board™ is a low-power audio amplifier with a digital volume control. It is equipped with the LM4860, an audio amplifier IC capable of delivering up to 1W of continuous power to an 8Ω load. It has a very low total harmonic distortion (THD) of less than 1% over the entire audio spectrum, which makes it perfectly suited for small boom-boxes, PC speakers, and similar low-power sound reinforcing devices that can be powered by batteries. A high integration level of the LM4860 IC allows an additional circuit for digital signal attenuation to be used, offering 8 different volume levels, selectable over 3 GPIO pins of the mikroBUS.

    AudioAmp 4 Click Board™ is supported by the mikroSDK compliant library, which includes functions that simplify software development. The Click Board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS slot.

    Not rated yet
    • $18.21
    • Including 20% UK VAT*
  • AudioAmp 5 Click Board™

    The Audio Amp 5 Click Board™ is a stereo audio amplifier, capable of delivering up to 10W per channel with the 8Ω load. It is based on the TPA3138D2, a class-D integrated amplifier, which utilises a highly efficient switching scheme. With about 20mA in idle mode, it allows for longer operation and improved thermal performance, making it a perfect choice for various battery-powered applications. Advanced EMI Suppression with Spread Spectrum Control allows using ferrite bead filters instead of bulky inductors, still maintaining the required EMC levels. The TPA3138D2 IC is equipped with a set of protection features, allowing a reliable operation.

    Audio Amp 5 Click Board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click Board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS socket.

    Not rated yet
    • $18.21
    • Including 20% UK VAT*
  • AudioAmp 6 Click Board™

    The AudioAmp 6 Click Board™ is a mono/subwoofer audio amplifier, capable of delivering up to 18.5W with the 4Ω load. It is based on the TPA3138D2, a class-D integrated amplifier, which utilizes a highly efficient switching scheme. With about 20mA in idle mode, it allows for longer operation and improved thermal performance, making it a perfect choice for various battery-powered applications. Advanced EMI Suppression with Spread Spectrum Control allows using ferrite bead filters instead of bulky inductors, still maintaining the required EMC levels. The TPA3138D2 IC is equipped with a set of protection features, allowing a reliable operation.

    Not rated yet
    • $14.99
    • Including 20% UK VAT*
  • AudioAmp Click Board™

    AudioAmp Click Board™ is a mikroBUS add-on board that functions as a mono audio amplifier. It is driven by a Texas Instruments LM48100Q-Q1 Boomer Mono, 1.3W Audio Power Amplifier IC.

    Not rated yet
    • $14.99
    • Including 20% UK VAT*
  • AudioMUX Click Board™

    The AudioMUX Click Board™ Board™ is a sound processing Click Board™ with digital controls, based on the TDA7468D IC. It can be used to select one of four audio input channels, adjust its frequency response and volume, and send it to the output. There is also a BASS ALC section implemented on this IC, keeping the base in control even on higher volume settings. Independent LEFT and RIGHT channel volume control, complete control over the I2C interface, a full set of 3.5mm vertical jack connectors on-board All these features make this Click Board™ a very good solution for the development of all kinds of audio applications.

    AudioMUX Click Board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click Board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS socket.

    Not rated yet
    • $52.48
    • Including 20% UK VAT*
  • BT Audio Click Board™

    The BT Audio Click Board™ is ideal if you are getting tired of all those cables you need just to listen to your favorite song over speakers, what you need is BT Audio Click Board™ with Microchip's RN52 Bluetooth audio module.

    With on-board 3.5mm jacks for both a microphone and a speaker, this is a complete solution for streaming audio from a smartphone or PC over a wireless connection.

    Not rated yet
    • $52.48
    • Including 20% UK VAT*
  • EVC Click Board™

    The EVC Click Board™ is a six-channel digital volume controller, equipped with an integrated electronic volume control circuit, which can be controlled over the I2C interface. The PT2258 IC offers six individual input channels, each with the attenuation range between 0 and -79dB, in 1dB steps. This chip requires a minimum number of external components, simplifying its implementation in a wide range of modern audio application. As an audio circuit, EVC Click Board™ features very low noise and high Signal to Noise ratio (SNR) of more than 100dB. Low Total Harmonic Distortion (THD) of 0.005% ensures absolute sound clarity.

    Not rated yet
    • $18.21
    • Including 20% UK VAT*
  • Mic 2 Click Board™

    The MIC 2 Click Board™ is equipped with a small electret microphone, accompanied by a suitable preamplifier circuit. The small electret microphone is not capable of providing sufficient line-level output; therefore, the pre-amp has to be used. The pre-amp circuit consists of a dual op-amp and a digitally controlled potentiometer IC. Thanks to the AD5171, it is possible to control the feedback loop gain of the MCP6022 op-amp over the I2C interface, in 64 discrete steps. The AD5171 digital potentiometer IC can lock-out its wiper by means of OTP fuse bit: once locked, it will permanently retain the programmed value.

    MIC 2 Click Board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click Board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $16.07
    • Including 20% UK VAT*
  • Mic Click Board™

    The Mic Click Board™ is based on the SPQ0410HR5H-B surface mount silicon microphone with maximum RF protection.

    The Click Board™ is designed to run on a 3.3V power supply. It communicates with the target microcontroller over the AN pin on the MikroBUSline.

    Not rated yet
    • $9.64
    • Including 20% UK VAT*
  • MP3 2 Click Board™

    The MP3 2 Click Board™ is an audio decoder expansion board with on-board microSD card slot, that enables you to create your personal audio playback system. It holds the KT403A,a SOC chip solution with intergraded MCU, hardware audio MP3/WAV decoder and DSP, from Shenzhen Qianle Microelectronics Technology Co. Ltd. 

    All the mentioned integrated hardware components enable the MP3 2 Click Board™ board to guarantee good stability and tone quality. You are able to use UART serial communication to control this board and do diverse operations with music files from microSD card such as Play, Pause, Volume Up/Down, any many more. These features make MP3 2 Click Board™ the ideal solution for audio device, in any application that demands an Audio Playback Module for MP3, WAV.

    Not rated yet
    • $18.21
    • Including 20% UK VAT*
Products: 116 of 19

Bestsellers

* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.