Motor Control Click Boards™

Products: 116 of 45
  • Brushless 2 Click Board™

    The Brushless 2 Click Board™ is fitted with the DRV10964 BLDC motor controller with an integrated output stage. The Click Board™ is designed to run on either 3.3V or 5V power supply.

    It communicates with the target microcontroller over the following pins on the MikroBUSline: AN, RST, CS, PWM, INT.

    Not rated yet
    • $21.67
    • Including 20% UK VAT*
  • Brushless 3 Click Board™

    The Brushless 3 Click Board™ carries the DRV10983, a three-phase sensor-less motor driver with integrated power MOSFETs. When an external power supply is applied, you can drive a brush-less DC motor through the PWM pin, AN pin or I2C interface.

    It communicates with the target microcontroller over I2C interface, with the additional functionality provided by the following pins on the mikroBUS line: PWM, AN, INT, RST.d.

    Not rated yet
    • $24.22
    • Including 20% UK VAT*
  • Brushless 4 Click Board™

    The Brushless 4 Click Board™ is a 3 phase sensorless BLDC motor driver, which features a 180' sinusoidal drive, providing high efficiency and low acoustic noise. This type of drivers inherently provides higher torque in general, compared to classical 120' BLDC motor drivers. Brushless 4 Click Board™ allows a wide voltage range to be used for the power supply: from 2V, up to 14V. The Click Board™ features a standard set of protection features: over-voltage protection, over-temperature protection, over-current limiting, but also some more specific protection features, such as the rotor lock-up protection and automatic restart function.

    Not rated yet
    • $24.22
    • Including 20% UK VAT*
  • Brushless 5 Click Board™

    The Brushless 5 Click Board™ is a 3 phase sensorless BLDC motor controller, with a soft-switching feature for reduced motor noise and EMI, and precise BEMF motor sensing, which eliminates the need for Hall-sensors in motor applications. It can drive 5V-16V motors with up to 500 mA current. The motor driver allows speed control via the PWM signal from the host MCU. It also features an output pin for reading the speed of the motor. Delayed phase commutation ensures a reliable motor start, while the Lock Detect function prevents damage and overheating.

    Not rated yet
    • $24.22
    • Including 20% UK VAT*
  • Brushless 6 Click Board™

    The Brushless 6 Click Board™ is designed to drive a three-phase sensorless, brushless motor, also known as the BLDC motor. The motor rotation is controlled by receiving driving commands via the incoming PWM signal. This Click Board™ fully controls the rotation of the BLDC motor by utilizing the on-board MCU ATmega8A, an 8-bit MCU from Microchip. The on-board MCU outputs are not adequate to power on the coils of the BLDC motor directly, so this MCU is used to control the power circuitry, instead. This circuit consists of 6 MOSFET transistors, used to switch the power from an external power source to the appropriate stator coils.

    Not rated yet
    • $34.41
    • Including 20% UK VAT*
  • Brushless 7 Click Board™

    The Brushless 7 Click Board™ is, as its name said, a motor driver based expansion board for controlling BLCD motors with any microcontroller. The board is based on TC78B009FTG IC from Toshiba, which is a three-phase BLDC motor controller that does not require Hall sensors. 

    Some of the main features are a built-in closed loop speed control function that regulates and maintains the motor rotational speed under dynamic power fluctuations and load variations. With precise setting of a speed profile done by the built-in nonvolatile memory (NVM) it eliminates the need for an external MCU for closed loop speed control and makes it perfect solution for applications that include high-speed fans used in servers, blowers, cordless vacuum cleaners, and robot vacuum cleaners.

    Not rated yet
    • $31.86
    • Including 20% UK VAT*
  • Brushless Click Board™

    The Brushless Click Board™ carries Toshiba's TB6575FNG IC for driving 3-phase full-wave Brushless DC motors ' which are ideal for powering flying drones.

    Not rated yet
    • $49.71
    • Including 20% UK VAT*
  • DC Motor 10 Click Board™

    DC Motor 10 Click Board™ is a brushed DC motor driver with the current limiting and current sensing. It is based on the TLE 6208-6 G, an Hex-Half-Bridge / Double Six-Driver IC, optimised for motor driving applications. It can be operated SPI communication interface, allowing to drive the connected motors in three different ways: it can be used as a free configurable as switch, half-bridge or H-bridge, offering an additional speed control and direction options. The TLE 6208-6 G also contains a set of protection features, offering a very high level of reliability. Besides driving capabilities, DC Motor 10 Click Board™ can also sense current consumption at its output.

    Not rated yet
    • $21.67
    • Including 20% UK VAT*
  • DC Motor 11 Click Board™

    The DC Motor 11 Click Board™ is a brushed DC motor driver with the current limiting and current sensing. It is based on the DRV8830, an integrated H-Bridge driver IC, optimised for motor driving applications. It can be operated by two logic signals, allowing to drive the connected motor in two different ways: it can use fixed logic levels for the direction control, or it can be controlled by a PWM signal, offering an additional speed control option. The DRV8830 also contains a set of protection features, offering a very high level of reliability. Besides driving capabilities, DC Motor 11 Click Board™ can also sense current consumption at its output.

    Not rated yet
    • $19.12
    • Including 20% UK VAT*
  • DC Motor 14 Click Board™

    The DC MOTOR 14 Click Board™ is a PWM chopper type brushed DC motor driver, labeled as TB67H450FNG. This IC includes one channel of motor output block, using a wide range of supply voltages, while delivering reasonably high current to the connected DC motors. Low ON-resistance MOSFETs and a PWM control help the TB67H450FNG exhibit lower heat generation thus efficient motor drive. Furthermore, the TB67H450FNG has two inputs, IN1 and IN2, which allow for selection of the four operation modes; forward (clockwise), reverse (counter-clockwise), short brake, and stop modes.

    The Click board™ is supported by the mikroSDK compliant library, which includes functions that simplify software development. The Click board™ comes as a fully tested product, ready to be used on a system equipped with mikroBUS™.

    Not rated yet
    • $17.84
    • Including 20% UK VAT*
  • DC Motor 2 Click Board™

    The DC MOTOR 2 Click Board™ is based on the TB6593FNG driver IC for direct current motors. With two pairs of screw terminals (power supply and outputs), the Click Board™ can drive motors with voltages from 2.5 to 13V.

    Not rated yet
    • $17.84
    • Including 20% UK VAT*
  • DC Motor 3 Click Board™

    The DC MOTOR 3 Click Board™ is a MikroBUS add-on board with a Toshiba TB6549FG full-bridge driver for direct current motors. The IC is capable of outputting currents of up to 3.5 A with 30V, making it suitable for high-power motors.

    Not rated yet
    • $24.22
    • Including 20% UK VAT*
  • DC Motor 4 Click Board™

    The DC MOTOR 4 Click Board™ is capable of driving motors with a supply voltage from 4.5V to 36V. It carries the MAX14870 motor driver from Maxim Integrated.

    The Click Board™ is designed to run on either 3.3V or 5V power supply. DC MOTOR 4 Click Board™ communicates with the target MCU over the following pins on the MikroBUS line: PWM, AN, CS, and INT.

    Not rated yet
    • $19.12
    • Including 20% UK VAT*
  • DC Motor 5 Click Board™

    The DC MOTOR 5 Click Board™ carries the DRV8701 brushed DC motor gate driver from Texas Instruments.

    The Click Board™ is designed to run on an external power supply. It communicates with the target MCU over the following pins on the MikroBUS line: AN, RST, CS, PWM, and INT.

    Not rated yet
    • $21.67
    • Including 20% UK VAT*
  • DC Motor 6 Click Board™

    The DC Motor 6 Click Board™ is a PWM chopper type brushed DC motor driver, labeled as TB67H451FNG. This IC includes one channel of motor output block, using a wide range of supply voltages, while delivering reasonably high current to the connected DC motors. Low ON-resistance MOSFETs and a PWM control help the TB67H451FNG exhibit lower heat generation thus efficient motor drive. Furthermore, the TB67H451FNG has two inputs, IN1 and IN2, which allow for selection of the four operation modes; forward (clockwise), reverse (counter-clockwise), short brake, and stop modes.

    DC Motor 6 Click board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $15.29
    • Including 20% UK VAT*
  • DC Motor 7 Click Board™

    The DC Motor 7 Click Board™ is a dual brushed DC motor driving Click Board™, featuring the advanced PWM chopper-type integrated DC motor driver, labelled as TB67H400AFTG. This IC can drive two brushed DC motors independently, using a wide range of supply voltages, while delivering reasonably high current to the connected DC motors. This is possible due to the low resistance of the integrated H-Bridges. In addition to being able to drive two independent DC motors, it can be used in a so-called large mode to drive a single motor, utilising both bridges in parallel. This effectively doubles the amount of current it can deliver to the DC motor.

    Not rated yet
    • $24.22
    • Including 20% UK VAT*
Products: 116 of 45

Bestsellers

* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.