Brushed Motor Click Boards™

Products: 16 of 6
  • DC Motor 10 Click Board™

    DC Motor 10 Click Board™ is a brushed DC motor driver with the current limiting and current sensing. It is based on the TLE 6208-6 G, an Hex-Half-Bridge / Double Six-Driver IC, optimised for motor driving applications. It can be operated SPI communication interface, allowing to drive the connected motors in three different ways: it can be used as a free configurable as switch, half-bridge or H-bridge, offering an additional speed control and direction options. The TLE 6208-6 G also contains a set of protection features, offering a very high level of reliability. Besides driving capabilities, DC Motor 10 Click Board™ can also sense current consumption at its output.

    Not rated yet
    • $21.73
    • Including 20% UK VAT*
  • DC Motor 11 Click Board™

    The DC Motor 11 Click Board™ is a brushed DC motor driver with the current limiting and current sensing. It is based on the DRV8830, an integrated H-Bridge driver IC, optimised for motor driving applications. It can be operated by two logic signals, allowing to drive the connected motor in two different ways: it can use fixed logic levels for the direction control, or it can be controlled by a PWM signal, offering an additional speed control option. The DRV8830 also contains a set of protection features, offering a very high level of reliability. Besides driving capabilities, DC Motor 11 Click Board™ can also sense current consumption at its output.

    Not rated yet
    • $19.17
    • Including 20% UK VAT*
  • DC Motor 4 Click Board™

    The DC MOTOR 4 Click Board™ is capable of driving motors with a supply voltage from 4.5V to 36V. It carries the MAX14870 motor driver from Maxim Integrated.

    The Click Board™ is designed to run on either 3.3V or 5V power supply. DC MOTOR 4 Click Board™ communicates with the target MCU over the following pins on the MikroBUS line: PWM, AN, CS, and INT.

    Not rated yet
    • $19.17
    • Including 20% UK VAT*
  • DC Motor 5 Click Board™

    The DC MOTOR 5 Click Board™ carries the DRV8701 brushed DC motor gate driver from Texas Instruments.

    The Click Board™ is designed to run on an external power supply. It communicates with the target MCU over the following pins on the MikroBUS line: AN, RST, CS, PWM, and INT.

    Not rated yet
    • $21.73
    • Including 20% UK VAT*
  • DC Motor 7 Click Board™

    The DC Motor 7 Click Board™ is a dual brushed DC motor driving Click Board™, featuring the advanced PWM chopper-type integrated DC motor driver, labelled as TB67H400AFTG. This IC can drive two brushed DC motors independently, using a wide range of supply voltages, while delivering reasonably high current to the connected DC motors. This is possible due to the low resistance of the integrated H-Bridges. In addition to being able to drive two independent DC motors, it can be used in a so-called large mode to drive a single motor, utilising both bridges in parallel. This effectively doubles the amount of current it can deliver to the DC motor.

    Not rated yet
    • $24.28
    • Including 20% UK VAT*
  • DC Motor 9 Click Board™

    The DC Motor 9 Click Board™ is a brushed DC motor driver with the current limiting and current sensing. It is based on the DRV8871, an integrated H-Bridge driver IC, optimised for motor driving applications. It can be operated by two logic signals, allowing to drive the connected motor in two different ways: it can use fixed logic levels for the direction control, or it can be controlled by a PWM signal, offering an additional speed control option. The DRV8871 also contains a set of protection features, offering a very high level of reliability. Besides driving capabilities, DC Motor 9 Click Board™ can also sense current consumption at its output.

    Not rated yet
    • $23.00
    • Including 20% UK VAT*

Bestsellers

* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.