Brushless Motor Click Boards™

Products: 110 of 10
  • Brushless 2 Click Board™

    The Brushless 2 Click Board™ is fitted with the DRV10964 BLDC motor controller with an integrated output stage. The Click Board™ is designed to run on either 3.3V or 5V power supply.

    It communicates with the target microcontroller over the following pins on the MikroBUSline: AN, RST, CS, PWM, INT.

    Not rated yet
    • $18.27
    • Including 20% UK VAT*
  • Brushless 3 Click Board™

    The Brushless 3 Click Board™ carries the DRV10983, a three-phase sensor-less motor driver with integrated power MOSFETs. When an external power supply is applied, you can drive a brush-less DC motor through the PWM pin, AN pin or I2C interface.

    It communicates with the target microcontroller over I2C interface, with the additional functionality provided by the following pins on the mikroBUS line: PWM, AN, INT, RST.d.

    Not rated yet
    • $20.42
    • Including 20% UK VAT*
  • Brushless 4 Click Board™

    The Brushless 4 Click Board™ is a 3 phase sensorless BLDC motor driver, which features a 180' sinusoidal drive, providing high efficiency and low acoustic noise. This type of drivers inherently provides higher torque in general, compared to classical 120' BLDC motor drivers. Brushless 4 Click Board™ allows a wide voltage range to be used for the power supply: from 2V, up to 14V. The Click Board™ features a standard set of protection features: over-voltage protection, over-temperature protection, over-current limiting, but also some more specific protection features, such as the rotor lock-up protection and automatic restart function.

    Not rated yet
    • $20.42
    • Including 20% UK VAT*
  • Brushless 5 Click Board™

    The Brushless 5 Click Board™ is a 3 phase sensorless BLDC motor controller, with a soft-switching feature for reduced motor noise and EMI, and precise BEMF motor sensing, which eliminates the need for Hall-sensors in motor applications. It can drive 5V-16V motors with up to 500 mA current. The motor driver allows speed control via the PWM signal from the host MCU. It also features an output pin for reading the speed of the motor. Delayed phase commutation ensures a reliable motor start, while the Lock Detect function prevents damage and overheating.

    Not rated yet
    • $20.42
    • Including 20% UK VAT*
  • Brushless 6 Click Board™

    The Brushless 6 Click Board™ is designed to drive a three-phase sensorless, brushless motor, also known as the BLDC motor. The motor rotation is controlled by receiving driving commands via the incoming PWM signal. This Click Board™ fully controls the rotation of the BLDC motor by utilizing the on-board MCU ATmega8A, an 8-bit MCU from Microchip. The on-board MCU outputs are not adequate to power on the coils of the BLDC motor directly, so this MCU is used to control the power circuitry, instead. This circuit consists of 6 MOSFET transistors, used to switch the power from an external power source to the appropriate stator coils.

    Not rated yet
    • $29.02
    • Including 20% UK VAT*
  • Brushless 7 Click Board™

    The Brushless 7 Click Board™ is, as its name said, a motor driver based expansion board for controlling BLCD motors with any microcontroller. The board is based on TC78B009FTG IC from Toshiba, which is a three-phase BLDC motor controller that does not require Hall sensors. 

    Some of the main features are a built-in closed loop speed control function that regulates and maintains the motor rotational speed under dynamic power fluctuations and load variations. With precise setting of a speed profile done by the built-in nonvolatile memory (NVM) it eliminates the need for an external MCU for closed loop speed control and makes it perfect solution for applications that include high-speed fans used in servers, blowers, cordless vacuum cleaners, and robot vacuum cleaners.

    Not rated yet
    • $26.87
    • Including 20% UK VAT*
  • Brushless Click Board™

    The Brushless Click Board™ carries Toshiba's TB6575FNG IC for driving 3-phase full-wave Brushless DC motors ' which are ideal for powering flying drones.

    Not rated yet
    • $41.92
    • Including 20% UK VAT*
  • Fan 4 Click Board™

    The Fan 4 Click Board™ is a very compact, two-wire fan driver. It utilizes an integrated 5V, DC, brushless-motor driver chip. Its output voltage regulation and current limiting capabilities allow the speed control for the two-wire DC brushless motors. The Click Board™ uses the LTC1695 IC, which features an integrated 6-bit DAC. The DAC regulates the output voltage in the range from 0 to 4.92V. This IC also has some additional features, such as the maximum output current limiting, and thermal shutdown protection. There is also a startup boost timer which ensures reliable startup of the fan, connected to the output terminal.

    Not rated yet
    • $16.12
    • Including 20% UK VAT*
  • Fan 6 Click Board™

    The Fan 6 Click Board™  features the EMC2103, an SMBus compliant fan controller with up to up to 3 external and 1 internal temperature channels. The fan driver can be operated using two methods each with two modes. The methods include an RPM based Fan Speed Control Algorithm and a direct PWM drive setting. The modes include manually programming the desired settings or using the internal programmable temperature look-up table to select the desired setting based on measured temperature. And MIC2253 a high power-density, 1 MHz PWM DC/DC boost regulator which allows driving 12V fan.

    Not rated yet
    • $17.20
    • Including 20% UK VAT*
  • STSPIN233 Click Board™

    The STSPIN233 Click Board™ is a complete solution for a 3-phase integrated motor driver, based on the STSPIN233, Low voltage 3-phase integrated motor driver. It is optimized for battery-powered, low voltage motor driving applications, featuring the lowest standby current available on the market (max 80 nA). 

    The STSPIN233 is a high-efficiency motor driver, featuring low ON resistance MOSFETs as the output stage, and extremely low leakage current (max 1µA). Its output stage implements the PWM current control with fixed OFF time, along with a full set of protection features. The device can be used with the step motor voltage ranging from 1.8V to 10V, and current up to 1.3A per bridge.

    Not rated yet
    • $18.27
    • Including 20% UK VAT*
* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.