Click Boards based on power supply control devices.

Power Management Click Boards™

Products: 116 of 69
  • 3xBuck Click Board™

    The 3xBuck Click Board™ is a triple step-down (buck) converter Click Board™. It features three independent output terminals that can provide 1.8V, 3.3V, and 5V with the combined current output up to 3A. This specific selection of output voltages makes this Click Board™ a perfect choice for an embedded application power supply, as these voltages are the most commonly used values. The voltage at each output can be switched to a programmable internal voltage divider, in cases when the output voltage fine-tuning is required. This can be done over the industry-standard I2C interface.

    Not rated yet
    • $37.63
    • Including 20% UK VAT*
  • Balancer 2 Click Board™

    The Balancer 2 Click Board™ is an overvoltage protection device for a 2-series cell lithium-ion battery. Click contains two separate overvoltage battery detection circuits and automatic cell imbalance correction. It can be used for various applications, power tools, portable equipment, and instrumentation, to energy storage systems (ESS), while providing the output voltage at the same time. By utilizing an externally connected power supply, it can charge 2-cell Li-Ion batteries.

    The Click board™ is supported by the mikroSDK compliant library, which includes functions that simplify software development. The Click board™ comes as a fully tested product, ready to be used on a system equipped with mikroBUS™.

    Not rated yet
    • $16.13
    • Including 20% UK VAT*
  • Balancer 3 Click Board™

    The Balancer 3 Click Board™ is overvoltage protection device for 2-series cell lithium-ion battery packs that incorporates a high-accuracy precision overvoltage detection circuit and automatic cell imbalance correction. It can be used for various applications, ranging from smartphones, notebook / laptops, power tools, portable equipment and instrumentation, to energy storage systems (ESS), while providing the output voltage at the same time.

    The Click Board™ is supported by the mikroSDK compliant library, which includes functions that simplify software development. The Click Board™ comes as a fully tested product, ready to be used on a system equipped with mikroBUS™.

    Not rated yet
    • $12.90
    • Including 20% UK VAT*
  • Balancer 5 Click Board™

    The Balancer 5 Click Board™ is an intelligent 2-cell Li-Ion battery charger, system power manager, and a battery fuel gauge Click Board™. 

    Balancer 5 Click Board™ is based on BQ25887 controller which has some extra features enabling charging without too much hassle. As a system power distributor, it can supply up to 3.3A to a connected battery. By utilizing an externally connected USB power supply, it can charge a 2-cell Li-Ion battery. A dedicated power management IC with the optimized smart power control allows very efficient management of the available power.  

    Not rated yet
    • $16.13
    • Including 20% UK VAT*
  • BATT-MAN Click Board™

    The BATT-MAN Click Board™ is a very versatile battery operated power manager. When powered via mikroBUS, it will charge the connected Li-Ion/Li-Po 3.7V battery, while providing the output voltage on all its outputs at the same time. The interesting feature of this device is that it can provide additional current to the connected load if the current provided from the mikroBUS socket is not enough. This is possible by utilizing the connected battery and by employing intelligent power routing algorithms of BATT-MAN Click Board™.

    Not rated yet
    • $29.03
    • Including 20% UK VAT*
  • BATT-MON Click Board™

    The BATT-MON Click Board™ is a very versatile, high accuracy, multiple-chemistry battery gauge for applications single-cell batteries. It can be used for various applications, ranging from smartphones, notebook / laptops, power tools, vacuums, to energy storage systems (ESS), while providing the output voltage at the same time. The interesting feature of this device is that it can provide additional current to the connected load if the current provided from the mikroBUS™ socket is not enough. This is possible by utilizing the connected battery and by employing intelligent power routing algorithms of BATT-MON Click Board™.

    Not rated yet
    • $13.98
    • Including 20% UK VAT*
  • Boost 2 Click Board™

    The BOOST 2 Click Board™ is a DC-DC step-up (boost) regulator that has a fixed 5V output, which can be obtained from any low voltage input - such as NiCd, NiMH or one cell Li-Po/Li-Ion batteries. This Click Board™ features very high efficiency, low noise and anti-ringing voltage output and inrush current limiting with the internal soft-start, as well as true disconnect option for minimized power drain, when in shutdown mode.

    Not rated yet
    • $16.13
    • Including 20% UK VAT*
  • Boost 3 Click Board™

    The Boost 3 Click Board™ is a compact add-on board that contains a boost converter with an integrated current mirror function. This board features the TPS61391, a 700-kHz pulse-width modulating (PWM) Step-Up converter with a 70V switch FET with an input voltage up to 5.5V from Texas Instruments. The TPS61391 includes an accurate current mirror, with two selectable gain options (1:5 or 4:5), and provides high optical-power protection with an additional FET in series with the APD power path, with the typical response time of 0.5µs. This Click board™ is designed to be used for applications such as biasing and monitoring the avalanche photodiodes (APD) in the optical receivers, but it also can be used as a high voltage sensor supply or in battery-powered and automotive applications.

    Boost 3 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $16.13
    • Including 20% UK VAT*
  • Boost 4 Click Board™

    The Boost 4 Click Board™ carries the TPS61230A, a high efficiency fully integrated synchronous boost converter from Texas Instruments. The Click Board™ is designed to run on a 3.3V power supply.

    Boost 4 Click Board™ drives the target chip through the digi pot, which has SPI communication with the microcontroller on the system.

    Not rated yet
    • $18.28
    • Including 20% UK VAT*
  • Boost 6 Click Board™

    The Boost 6 Click Board™ features the TPS55332-Q1, a monolithic high-voltage switching regulator with integrated 3-A, 60-V power MOSFET. The device can be configured as a switch mode step-up power supply with voltage supervisor. This Click board™ can be used for applications regarding lighting, battery powered and automotive applications.

    The Boost 6 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $16.13
    • Including 20% UK VAT*
  • Boost Click Board™

    Use our new boost converter to step up the voltage in your next project.

    The Boost Click Board™ is based on Microchip's MIC2606, a 2MHz, PWM DC/DC boost switching regulator available in a 2mm x 2mm MLF' package.

    Boost Click Board™ provides an adjustable output voltage through the on-board DAC that drives the FB pin of the MIC2606 to set desired output voltage. The Click Board™ also has an on-board ADC that converts output voltage and sends its digital value through SPI pins of mikroBUS to the microcontroller.

    Not rated yet
    • $22.58
    • Including 20% UK VAT*
  • Boost-INV 2 Click Board™

    The Boost-INV 2 Click Board™ is a very useful DC/DC voltage converter device, as can output both positive and negative voltage, boosted up to 15V and inverted to -15V, from a single fixed voltage input. The input voltage can vary between 2.7V to 5.5V, making the Boost-INV 2 Click Board™ an ideal solution for powering devices with complex, split-rail power supply demands, using only a common battery. The Click Board™ is equipped with two additional D/A converters, which make it possible to digitally set the output voltage, via the SPI.

    Not rated yet
    • $31.18
    • Including 20% UK VAT*
  • Boost-INV Click Board™

    The Boost-INV Click Board™ is a very useful DC/DC voltage converter device, as can output both positive and negative voltage, boosted up to 12.78V and -13.95, from a single fixed voltage input. The input voltage can vary between 2.55V to 5.5V, making the Boost-INV Click Board™ an ideal solution for powering devices with complex, split-rail power supply demands, using only a common battery. A special feature of the LT3582 integrated DC/DC converter is the presence of the I2C interface, which is uncommon for devices of this type: it allows configuring of the output voltages, power sequencing, and output voltage ramp rates. It has an OTP memory also, which can be used to store the power-on default values.

    Not rated yet
    • $22.58
    • Including 20% UK VAT*
  • Buck & Boost Click Board™

    The Buck & Boost Click Board™ is a compact add-on board that contains a configurable power management device. This board features the MIC7401, a highly-integrated power-management IC featuring five synchronous buck regulators, one boost regulator, and a high-speed I2C interface with an internal EEPROM memory from Microchip. The MIC7401 offers two distinct modes of operation (Standby and Normal) and includes a global enable pin to shut down the device for additional power savings. Some features of this Click board™ like an energy-optimized solution, flexibility, and high-performance make it an excellent choice for portable handheld and infotainment applications.

    Buck & Boost Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $74.19
    • Including 20% UK VAT*
    Out of Stock - Order Now, Ships within 5 days
  • Buck 10 Click Board™

    The Buck 10 Click Board™ is a high-efficiency step-down converter which provides a highly regulated output voltage derived from the connected power source, rated from 4V to 18V. The regulated output voltage can be selected between two values: 3.3V and 5V. These are voltage values that are most commonly used in many embedded designs. 

    This Click Board™ is based around an integrated DC-DC converter, the MPM3632C. Due to its high efficiency, MPM3632C allows the Click Board™ to easily deliver up to 3A of current. The MPM3632C is very reliable, offering over-current and over-voltage protection, as well as a thermal shutdown. 

    Not rated yet
    • $16.13
    • Including 20% UK VAT*
  • Buck 11 Click Board™

    The Buck 11 Click Board™ is a high-efficiency step-down converter which provides 3.3V on its output, derived from the connected power supply voltage, in the range from 4.2V to 60V. Buck 11 Click Board™ is based on the LMR36015, a highly efficient DC-DC step-down converter. In addition, the Buck 11 Click Board™ offers monitoring the stability of the output voltage by employing an additional A/D converter circuit. Due to its high efficiency, LMR36015 allows the Click Board™ to easily deliver up to 1.5A of current. The efficiency for lighter loads is optimized by using the PFM mode. It features a Hot Rod™ package which enables a low noise performance, high efficiency, and very compact size.

    Not rated yet
    • $22.58
    • Including 20% UK VAT*
Products: 116 of 69

Bestsellers

* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.