Temperature Sensor Click Boards™

Products: 116 of 56
  • DHT22 2 Click Board™

    The DHT22 2 Click Board™ is used for measuring the environmental temperature and relative humidity. It uses the CM2322 sensor, with very accurate thermal and humidity measuring capabilities. It can use either 1-Wire or I2C protocol to communicate with the integrated circuit.

    Attributes like the ultra-small size, low power consumption, signal transmission distance up to 20 meters, make this sensor the perfect choice for all kinds of applications that require measurement of the temperature and humidity.

    Not rated yet
    • $23.51
    • Including 20% UK VAT*
  • DHT22 Click Board™

    The DHT22 Click Board™ from Mikroelektronika is one of the simplest temperature and relative humidity sensor Click Board™ that carries the AM2302 sensor module, also known as DHT22. Concealed inside a plastic mesh packaging, the AM2302 temperature/humidity sensor needs just a single wire to communicate with the target board microcontroller.

    For added convenience, DHT22 Click Board™ is provided with two jumpers (zero Ω resistors). While one of them allows the user to choose between the MikroBUS pin to use (either CS or INT pin, which are SDA1 and SDA2 lines), the other on-board jumper allows the choice between 3.3V and 5V power supplies. The sensor generates the temperature/humidity data in a 16-bit resolution. The generated decimal number is 10 times the actual measurement, i.e., 216 would be 21.6.

    Not rated yet
    • $25.65
    • Including 20% UK VAT*
  • Fan 2 Click Board™

    The Fan 2 Click Board™ carries the MAX31760 precision fan-speed controller. It can measure temperature and adjust the fan speed to keep the temperature at the same level. Fan 2 Click Board™ can also control two fans at the same time.

    The Click Board™ is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over I2C interface, with additional functionality provided by the following pins on the MikroBUSline: INT, AN, RST, CS.

    Not rated yet
    • $16.03
    • Including 20% UK VAT*
  • Fan 3 Click Board™

    The Fan 3 Click Board™ is the perfect choice for speed control and it can operate in seven discrete speed steps. Unlike the PWM regulation which can sometimes cause the infamous coil whining effect on some types of fans, this Click Board™ outputs the selected voltage via the MIC29152 voltage regulator from Microchip, driven through the MIC74 - a serial to parallel I/O expander and a fan controller from the same company, keeping it constant at the output. Fan 3 Click Board™ works with 12V to 25V on its input connector and can be used whenever a noiseless solution with a variable fan speed is needed, for example - cooling of electronic components with the minimal possible noise produced.

    Not rated yet
    • $19.13
    • Including 20% UK VAT*
  • Fan 4 Click Board™

    The Fan 4 Click Board™ is a very compact, two-wire fan driver. It utilizes an integrated 5V, DC, brushless-motor driver chip. Its output voltage regulation and current limiting capabilities allow the speed control for the two-wire DC brushless motors. The Click Board™ uses the LTC1695 IC, which features an integrated 6-bit DAC. The DAC regulates the output voltage in the range from 0 to 4.92V. This IC also has some additional features, such as the maximum output current limiting, and thermal shutdown protection. There is also a startup boost timer which ensures reliable startup of the fan, connected to the output terminal.

    Not rated yet
    • $16.03
    • Including 20% UK VAT*
  • Fan 6 Click Board™

    The Fan 6 Click Board™  features the EMC2103, an SMBus compliant fan controller with up to up to 3 external and 1 internal temperature channels. The fan driver can be operated using two methods each with two modes. The methods include an RPM based Fan Speed Control Algorithm and a direct PWM drive setting. The modes include manually programming the desired settings or using the internal programmable temperature look-up table to select the desired setting based on measured temperature. And MIC2253 a high power-density, 1 MHz PWM DC/DC boost regulator which allows driving 12V fan.

    Not rated yet
    • $17.10
    • Including 20% UK VAT*
  • Fan Click Board™

    The Fan Click Board™ carries an EMC2301 controller for powering and regulating the operation of 5V four-wire fans, which are commonly utilized as coolers in computers and other electronics.


    .

    Not rated yet
    • $10.58
    • Including 20% UK VAT*
  • PHT Click Board™
    • New!

    PHT Click Board™

    The PHT Click Board™ is a compact add-on board that contains a PHT combo sensor. This board features the MS8607, a digital combination sensor providing 3 environmental measurements all-in-one: pressure, humidity, and temperature from TE Connectivity Measurement Specialties. This sensor is based on leading MEMS technologies, provides factory-calibrated PHT data available over an I2C serial interface. The standout feature of the MS8607, alongside its very respectable low power consumption at as low as 0.78 µA, is also ultra-low power consumption and high PHT accuracy. This Click board™ is appropriate for environmental monitoring, as well as PHT applications such as HVAC and weather stations.

    PHT Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $16.70
    • Including 20% UK VAT*
    Out of Stock - Order Now, Ships within 5 days
  • RTD 2 Click Board™

    The RTD 2 Click Board™ is a compact add-on board used for applications with resistive elements that change resistance over temperature. This board features the ADS1247, 24-bit analog-to-digital converter with a programmable gain amplifier (PGA) for sensor measurement applications from Texas Instruments. It features a precision delta-sigma (ΔΣ) ADC with a single-cycle settling digital filter, and an internal oscillator, but also provides a low-drift voltage reference, and two matched programmable excitation current sources (IDACs). It also integrates sensor burn-out detection, voltage bias for thermocouples, system monitoring, and digital GPIOs. This Click board™ is suitable for temperature sensor measurements such as RTDs, thermocouples and thermistors, for pressure measurements, process control, and many more.

    RTD 2 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $32.06
    • Including 20% UK VAT*
  • SHT AN Click Board™

    The SHT AN Click Board™  is a sensorics based add on board which can be used for measuring humidity and temperature. It features fully calibrated, linearized and temperature compensated SHT31-ARP-B sensor with analog output. This sensor is built on a new technology CMOSens® sensor chip from Sensirion

    What differentiate this Click Board™ board comparing to other is dual sensor analog output which can be used for measuring and calculation of the data over one analog output. This board is best suitable for the smart and low power applications which require temperature range of -40 to up to 90 °C. We have also in our offer SHT Click Board™, which is a digital interface version of the same sensor. 

    Not rated yet
    • $17.10
    • Including 20% UK VAT*
  • SHT Click Board™

    The SHT Click Board™ is a temperature and humidity sensing Click Board™ that carries Sensiron's SHT3x-DIS IC. Compared to its predecessor (SHT11), SHT3x Click Board™ has increased reliability and enhanced signal processing features with a high signal-to-noise ratio.

    Not rated yet
    • $27.78
    • Including 20% UK VAT*
  • Storm Chaser's Click Board™ Pack

    Storm Chaser's Click Board™ Pack.

    Not rated yet
    • $101.21
    • Including 20% UK VAT*
  • Surface Temp 2 Click Board™

    The Surface temp 2 Click Board™ is a compact add-on board that contains a high accuracy temperature sensor offering breakthrough performance over a wide industrial temperature range. This board features the ADT7422, a 16-bit I2C temperature sensor from Analog Devices. The ADT7422 features a precision ADC that provides 16-bit temperature measurement in the range of 25°C to 50°C with a resolution of 0.0078 °C and an accuracy of ± 0.1 °C. Also, it does not require additional calibration. This makes the Surface Temp Click an excellent choice for RTD and thermistor replacement, Vital Signs Monitoring (VSM), food transportation and storage, environmental monitoring, HVAC, and other applications.

    Surface temp 2 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $21.37
    • Including 20% UK VAT*
  • Surface Temp Click Board™

    The Surface temp Click Board™ is high accuracy digital temperature sensor Click Board™, offering breakthrough performance over a wide industrial range. It is equipped with the ADT7420 - an accurate 16-Bit Digital I2C temperature sensor from Analog Devices. It features high temperature accuracy, ultralow temperature drift (0.0073°C), fast first temperature conversion on power-up, no temperature calibration/correction required, and more useful features which makes this Click Board™ a great choise for RTD and thermistor replacement, medical equipment, food transportation and storage, environmental monitoring, HVAC, and many more.

    Not rated yet
    • $20.30
    • Including 20% UK VAT*
  • Temp-Log 2 Click Board™

    The Temp-Log 2 Click Board™ is a precise ambient temperature measurement device, equipped with 8Kbit (1024 bytes) of EEPROM memory, which can be used to permanently store system configuration or log application specific or user preference data. This Click Board™ covers a range of temperatures from -55°C to +125°C with the highest accuracy of ±0.5°C, in the range of 0°C to 85°C. The device can also send an ALERT signal to the INT pin of the mikroBUS every time programmed temperature thresholds are reached.

    Not rated yet
    • $16.03
    • Including 20% UK VAT*
  • Temp-Log 3 Click Board™

    The Temp-Log 3 Click Board™ is a temperature measuring Click Board™ featuring the MCP9843 IC, an accurate temperature sensor IC with integrated EEPROM. Besides the thermal sensor, this IC is equipped with additional 256 bytes of EEPROM. This can be a very useful option for some applications: it allows any data to be stored within the same IC, so no additional EEPROM IC is required. This can simplify the design, reducing the number of additional components. The thermal sensor itself includes some great features such as the programmable interrupt engine, measurement range from -20°C to +125°C, accuracy up to ±1°C typically, and more.

    Not rated yet
    • $12.82
    • Including 20% UK VAT*
Products: 116 of 56

Bestsellers

* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.