Serial Interface Click Boards™

Products: 116 of 36
  • 1-Wire I2C Click Board™

    The 1-Wire I2C Click Board™ carries the DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated. The Click Board™ runs on a 3.3V power supply.

    It communicates with the target microcontroller over 1-Wire.

    Not rated yet
    • $23.10
    • Including 20% UK VAT*
  • 8-Pin I2C Click Board™

    The 8-pin I2C Click Board™ is a compact add-on board that represents a breakout board that simplifies the connection of add-on boards with 8 pin Female Connector to mikroBUS™ socket. This board can be used as I2C Adapter with no main component on itself, with only an on-board connector for connection establishing. 8-pin I2C Click has no regional restrictions, no need for special permits, and it is possible to use this Click board™ worldwide. Being compatible with MFI (Made for iPod) is the most important feature of the 8-pin I2C Click board™ which ensures its proper operation with additional Apple accessories. This Click board™ is suitable for expanding the connectivity of the development system with the mikroBUS™, and ideal for communication with numerous devices that share the identical slave address on the same bus.

    8-pin I2C Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $31.50
    • Including 20% UK VAT*
  • ATA6563 Click Board™

    The ATA6563 Click Board™ carries the ATA6563 high-speed CAN transceiver. The Click Board™ is designed to run on a 5V power supply. Use the VIO SEL jumper for selecting the 3.3V or 5V logic level.

    It communicates with the target microcontroller over UART interface, with additional functionality provided by the AN pin on the MikroBUS line.

    Not rated yet
    • $21.00
    • Including 20% UK VAT*
  • ATA6570 Click Board™

    The ATA6570 Click Board™ is a CAN Partial Networking interface board. The Click Board™ carries the ATA6570, a high-speed CAN transceiver that interfaces a Controller Area Network (CAN) protocol controller and the physical two-wire CAN bus. This IC has some unique features that make it a perfect choice for any embedded CAN application.

    Not rated yet
    • $24.15
    • Including 20% UK VAT*
  • ATA663254 Click Board™

    The ATA663254 Click Board™ is a fully integrated LIN transceiver device with an integrated 5V LDO voltage regulator. The combination of voltage regulator and bus transceiver makes it possible to develop simple but powerful slave nodes in LIN bus systems. The integrated LDO can be used to provide power to the host MCU so that no additional voltage regulators are required, only the power supply connected to the LIN connector is needed. ATA663254 Click Board™ features the under-voltage protection, short-circuit protection, TXD time-out timer and its LIN physical layer complies with LIN 2.0, 2.1, 2.2, 2.2A and SAEJ2602-2 standard specifications.

    Not rated yet
    • $16.80
    • Including 20% UK VAT*
  • BroadR-Reach Click Board™

    The BroadR-Reach Click Board™ brings the industry grade communication standard to the mikroBUS, which is built to be used in an Ethernet-based open network. The Click Board™ is equipped with the BCM54811 Transceiver from Broadcom Limited, which is used to provide the hardware PHY layer for the network, and the W3150A+from WizNet, a hardware LSI protocol stack, that provides an easy and low-cost solution for high-speed Internet connectivity for digital devices by allowing simple installation of TCP/IP stack in the hardware.

    Not rated yet
    • $72.46
    • Including 20% UK VAT*
  • CAN Isolator Click Board™

    The CAN Isolator Click Board™ provides isolated CAN communication. It carries the ADM3053 signal and power isolated CAN transceiver with an integrated isolated DC-to-DC converter.

    The Click Board™ is designed to run on either 3.3V or 5V power supply. CAN Isolator Click Board™ communicates with the target microcontroller over UART interface.

    Not rated yet
    • $40.95
    • Including 20% UK VAT*
  • DMX Click Board™

    The DMX Click Board™  is a device used to establish communication between the MCU and equipment that uses the DMX512-A communication protocol. Unlike many similar solutions on the market, this unique device allows using the common UART data format, which is converted to an appropriate DMX512 format by the powerful PIC18F26K42 MCU from Microchip. This MCU has an integrated DMX peripheral, making it a perfect solution for such application. To allow interfacing with the DMX bus, DMX Click uses the RS485 transceiver from Analog Devices. Besides providing single-ended to differential signal conversion, this IC also provides the complete galvanic isolation from the DMX bus, without using any additional isolation components.

    DMX Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $30.45
    • Including 20% UK VAT*
  • Driver Click Board™

    The Driver Click Board™ features an IC with seven integrated high-current sink drivers, which can be used to drive a wide range of loads via simple parallel interface. These integrated drivers use high-efficiency MOSFETs for improved thermal performance. The DRV777 integrated motor and relay driver IC from Texas Instruments is the main active element of this Click Board™. It is ideally suited for driving motors, relays, and similar inductive loads, as it features an internal free-wheeling diode for inductive kickback protection, on every channel. It operates with voltages up to 20 V, and by combining all the channels, it can sink up to 1A of current.

    Not rated yet
    • $13.65
    • Including 20% UK VAT*
  • Expand 2 Click Board™

    The EXPAND 2 Click Board™ is an accessory board in mikroBUS form factor. It includes a 16-bit I/O expander MCP23017 with I°C clock speeds up to 10 MHz for higher throughput applications.

    Not rated yet
    • $12.60
    • Including 20% UK VAT*
  • Expand 3 Click Board™

    The EXPAND 3 Click Board™ carries DS2408, an 8-channel programmable I/O expander that communicates with the target board MCU through a standard Dallas Semiconductor 1-Wire interface (15.3 kbps or 100kbps).

    Not rated yet
    • $21.00
    • Including 20% UK VAT*
  • Expand 4 Click Board™

    The Expand 4 Click Board™ is intended for use as a port expander for connecting high power peripherals.

    It is based on the TPCIC6A595, a chip that combines an 8-bit serial-in, parallel-out shift register with an 8-bit D-type storage register.

    Not rated yet
    • $14.70
    • Including 20% UK VAT*
  • Expand 5 Click Board™

    The EXPAND 5 Click Board™  features a low-voltage 24-bit I2C and SMBus I/O expander. This 24-bit I/O expander is designed to provide general-purpose remote I/O expansion for most microcontroller families via the I2C serial interface. This Click Board™ features the TCA6424A from Texas Instruments, and it operates over a power supply voltage range of 1.65V to 5.5V. Wide voltage range allows the TCA6424A to interface with next-generation microprocessors and microcontrollers on the SDA/SCL side, where supply levels are dropping down to conserve power. The P-port outputs have high-current sink capabilities for directly driving LEDs while consuming low device current. 

    Not rated yet
    • $12.60
    • Including 20% UK VAT*
  • Expand 6 Click Board™

    The EXPAND 6 Click Board™ is a compact add-on board that contains an I2C configurable multi-port I/O expander with independently configurable pins as bi-directional input/outputs or PWM outputs. This board features the CY8C9520A, 20-bit I/O expander with EEPROM, and 4 independently configurable 8-bit PWM outputs from Cypress Semiconductor. The CY8C9520A operates as two I2C slave devices, first as a multi-port I/O expander, and second as a serial EEPROM with 3 Kbyte address space. It has a user default storage, flexible I2C address configuration, and a programmable interrupt function that indicates input pin level changes and PWM state changes. This Click board™ can be used to monitor and control LEDs and system intrusion detection devices, but also as a storage for information such as error codes or board manufacturing data for diagnostic purposes.

    EXPAND 6 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $17.06
    • Including 20% UK VAT*
  • Expand 7 Click Board™

    The EXPAND 7 Click Board™ is a compact add-on board that contains a multi-port I/O expander with bi-directional input/outputs or PWM outputs. This board features the CY8C9540A, 40-bit I/O port expander with EEPROM and 8 independently configurable 8-bit PWM outputs from Cypress Semiconductor. The CY8C9540A operates as two I2C slave devices, first as a multi-port I/O expander, and second as a serial EEPROM with 11 Kbyte address space. It has a user default storage, flexible I2C address configuration, and a programmable interrupt and reset function. This Click board™ can be used to monitor and control LEDs and system intrusion detection devices, but also as a storage for information such as error codes or board manufacturing data for diagnostic purposes.

    EXPAND 7 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $31.50
    • Including 20% UK VAT*
  • Expand Click Board™

    The Expand Click Board™ is an accessory board in mikroBUS form factor. It includes a 16-bit I/O expander MCP23S17 from Microchip with SPI clock speeds up to 10 MHz for higher throughput applications. 

    Not rated yet
    • $12.60
    • Including 20% UK VAT*
Products: 116 of 36

Bestsellers

* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.