Analog Interface Click Boards™

Products: 110 of 10
  • DAC 6 Click Board™

    DAC 6 Click is a compact add-on board that contains a fully-featured, general-purpose voltage-output digital-to-analog converter. This board features the DAC104S085, 10-bit, micro-power, a quad digital-to-analog converter with rail-to-rail output, from Texas Instruments. It uses the 3-wire SPI serial interface for communication, that operates at clock rates up to 40 MHz. Besides that, DAC 6 Click has also MCP1501 onboard, which is a high-precision, buffered, 2.048V voltage reference. Many features such as low power, rail-to-rail Voltage output, quad-channel output, and more, make it an excellent choice for use in battery-operated equipment, digital gain and offset adjustment, programmable voltage and current sources, and many more.

    DAC 6 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $19.17
    • Including 20% UK VAT*
    Out of Stock - Order Now, Ships within 5 days
  • Hall Current 2 Click Board™

    The Hall Current 2 Click Board™ is a very accurate current measurement Click Board™, which relies on the Hall effect. Its most distinctive feature is a very low series resistance of only 1.2mÃŽ©, making this device a nearly-perfect ampere meter. The maximum current which can be measured with the Hall current 2 ranges from -12A to +12A, with optimised precision. The measurement is thermally compensated and conditioned by the integrated sections of the hall sensor IC. The result is available via the I2C interface of the high precision, 12 bit AD converter, as well as in the analog form, from the analog pin of the microBUS, directly from the Hall effect current sensor IC. This Click Board™ does not require any current sensing resistors.

    Not rated yet
    • $23.00
    • Including 20% UK VAT*
  • Hall Current 3 Click Board™

    The Hall Current 3 Click Board™ is a very accurate current measurement Click Board™, which utilises the Hall effect to provide a precise and reliable measurement of reasonably high current. Its most distinctive feature is a very low series resistance of only 0.7mÃŽ©, making this device a nearly-perfect ammeter. The maximum current which can be measured by the MLX91210 integrated Hall sensor IC goes up to ±30A, but in respect to the nominal current measurement rating of the sensor, the current measurement is limited to about ±10A. The measurement is thermally compensated and conditioned by the high-speed integrated analog front-end sections of the Hall sensor IC. The current measurement value can be obtained from the on board 12-bit A/D converter, via the I2C interface.

    Not rated yet
    • $24.28
    • Including 20% UK VAT*
  • Hall Current 4 Click Board™

    The Hall Current 4 Click Board™ is designed to measure relatively high current by using the integrated ACS70331 sensor. The current sensor is based on the GMR elements for current measurement. The Hall Current 4 can be used for current measurement in the applications designed to follow a current, such as the applications for monitoring the current in battery chargers, or for the various kinds of system power supplies.

    Not rated yet
    • $23.00
    • Including 20% UK VAT*
  • Hall Current 5 Click Board™

    The Hall Current 5 Click Board™ is a very accurate electric current measurement Click Board™ based on the ACS733 IC. This IC is a galvanically isolated current sensor, which utilizes the Hall-effect principle. Its most distinctive feature is its very low series resistance of only 1 mΩ, which makes this device a nearly-perfect ammeter. The maximum current which can be measured with Hall current 5 Click Board™ ranges from -20 A to +20 A, with the optimised precision. By using the latest manufacturing technologies, the ACS733 can be used on very high frequencies, making it a perfect solution for a wide range of applications.

    Not rated yet
    • $23.00
    • Including 20% UK VAT*
  • Hall Current 6 Click Board™

    The Hall Current 6 Click Board™ is a very accurate current measurement Click Board™, based on the ACS723 IC. This IC is a galvanically isolated current sensor, which utilises the Hall-effect principle. Its most distinctive feature is its very low series resistance of only 0.65 mΩ, which makes this device a nearly-perfect ammeter. The maximum current which can be measured with Hall Current 6 Click Board™ ranges from -5 A to +5 A, with the optimised precision. It features a dedicated bandwidth selection pin, which allows better noise performance for a specific application.

    Not rated yet
    • $23.00
    • Including 20% UK VAT*
  • Hall Current Click Board™

    The Hall Current Click Board™ is a measurement add-on board intended to measure the current utilizing the Hall Effect. The board features a high-precision galvanically isolated TLI4970-D050T4 magnetic digital current sensor in a tiny footprint. The Hall current Click Board™ is equipped with two EXTreme ZPower connectors (IP- and IP+) to connect a conducting wire. Split the conducting wire and connect the ends to the two connectors. The current rail is galvanically isolated from the interface to the microcontroller to keep the surrounding circuitry safe. The sensor detects the strength of the current, then sends the measurement data to the target MCU through MikroBUS SPI (SDO, SCK and CS) lines.

    Hall current Click Board™ is based on contact-free measurement principle, which causes no additional power loss and makes it perfectly suited for high efficiency systems. It is designed to use a 3.3V power supply only. The board is an ideal choice for photovoltaic and general purpose inverters, power supplies (SMPS), battery chargers, lighting applications, and electrical drives.

    Not rated yet
    • $43.45
    • Including 20% UK VAT*
  • ISO ADC 2 Click Board™

    The ISO ADC 2 Click Board™ is a compact add-on board that represents a completely isolated 12-bit, 300 kSPS data acquisition system. This board features the AD7091R, successive-approximation analog-to-digital converter (ADC) from Analog Devices. It uses the 3-wire SPI serial interface for data communication, achieving up to 1 MSPS throughput rate. This Click board™ also features the ADuM5401, isolated DC-DC converter used to isolate the logic signals, power, and feedback paths in the DC-DC converter resulting in total isolation solution. Many features such as high throughput rate with ultralow power consumption, wide input bandwidth, accuracy, and speed make it an ideal choice for a wide variety of industrial measurements, data acquisition systems, monitoring functions, and many more.

    ISO ADC 2 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $57.51
    • Including 20% UK VAT*
    Out of Stock - Order Now, Ships within 5 days
  • Pot Click Board™

    The POT Click Board™ is a Click Board™ with the accurate selectable reference voltage output. By employing a high-quality 10mm carbon potentiometer, this Click Board™ can provide very accurate voltage output. POT 2 Click Board™ is also equipped with the SMD jumper, which allows the maximum reference voltage to be selected between two typically used values: 2.048V or 3.3V. The output is buffered with a rail-to-rail buffering operational amplifier, provides constant input and output impedance. The output current is limited by the protection circuit at the output, preventing damage if the output is shorted to GND.


    Not rated yet
    • $15.34
    • Including 20% UK VAT*
  • Waveform Click Board™

    The Waveform Click Board™ is a precise sine/triangle/square waveform generator, capable of reproducing frequencies up to 12MHz. It utilizes a Direct Digital Synthesis (DDS) IC made by Analog Devices, a company famed for its specialization in DSP development and engineering. The AD9833 waveform generator IC requires a very low count of additional components: besides the external clock source, it requires almost no components, allowing the Click Board™ to be equipped with some additional circuits. A digital potentiometer IC is used to attenuate the output signal, while the high-quality op-amp is used as a buffer.

    Not rated yet
    • $60.07
    • Including 20% UK VAT*
* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.