RS-485 Click Boards™

Products: 19 of 9
  • RS485 2 Click Board™

    The RS485 2 Click Board™ carries the MAX3471 half-duplex transceiver intended for lithium battery-powered RS-485/RS-422 applications.

    The Click Board™ is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface with additional functionality provided by the following pins on the MikroBUS line: PWM, CS..

    Not rated yet
    • $23.55
    • Including 20% UK VAT*
  • RS485 3 Click Board™

    The RS485 3 Click Board™ uses SN65HVD31DR from Texas Instruments, a tri-state differential line driver and differential input line receiver. The Click Board™ is intended to be used as UART to RS-422/RS-485 communication interface. It is suited for transmitting smaller blocks of data over long distances, using the four-wire bus, allowing for full-duplex communication.

    It can be used as a transceiver between UART interface and RS-422/RS-485 communication bus. RS485 3 Click Board™ can be used for controlling various building automation systems, light controllers, sensors and many small embedded devices that can all share the same bus, which can stretch up to 254 nodes and up to 1200m in length.

    Not rated yet
    • $26.17
    • Including 20% UK VAT*
  • RS485 4 Click Board™

    The RS485 4 Click Board™ offers an UART to RS485 signal conversion, featuring the ADM2795E specialised IC with the complete galvanic isolation. Digital input and output signals are transmitted across the isolation barrier by using the ICoupler', an IC scale transformer technology, which allows signals to be magnetically coupled across the isolation barrier within the IC, providing galvanic isolation for up to 5KV and data transfer rates up to 2.5Mbps. The ADM2795E is designed as a very robust and reliable UART to RS485 transceiver, allowing it to be used in very harsh industrial or other noisy environments.

    Not rated yet
    • $51.03
    • Including 20% UK VAT*
  • RS485 5 Click Board™

    The RS485 5 Click Board™ is equipped with the MAX485, low-power, slew-rate-limited transceiver for RS-485 and RS-422 communication, from Maxim Integrated. This device supports half-duplex RS-485 communication and can be used as an interface between the TTL level UART and the RS485 communication bus. 

    Thanks to the low power consumption and reduced slew-rate drivers that minimize EMI and reduce reflections caused by improperly terminated cables, error-free data transmission up to 250kbps is suported. 

    The RS485 5 Click Board™ Board is perfectly suitable for EMI-Sensitive Applications, such as industrial-control local area networks, building automation, HVAC systems, and many more.

    Not rated yet
    • $20.93
    • Including 20% UK VAT*
    Out of Stock - Order Now, Ships within 5 days
  • RS485 6 Click Board™

    The RS485 6 Click Board™ offers a half-duplex RS-485 communication with integrated surge protection, which can be used as an interface between the TTL level UART and the RS485 communication bus. It is based on THVD1429DT, a transceiver from Texas Instruments with signaling rate of up to 20 Mbps. This device features a wide common-mode voltage range from 3.3V to 5V, which makes it suitable for multi-point applications over long cable runs and noisy areas thanks to the integrated transient voltage suppressor (TVS) diodes in. This device and type of network is perfectly suitable for wireless infrastructure, building automation, HVAC systems or factory automation, and many more.

    RS485 6 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $20.93
    • Including 20% UK VAT*
  • RS485 Click Board™ 3.3V

    The RS-485 3.3V Click Board™ is a compact accessory board designed to add bidirectional data communication to the design. The board features a Texas Instruments SN65HVD12 differential line transceiver that provides high-speed bidirectional data communication on multipoint bus transmission lines. Compliant with EIA standards RS-485 and RS-422, this 3.3V version of RS485 Click Board™ is intended for balanced data transmission. RS485 Click Board™ 3.3V board features four screw terminals. The two terminals marked with.

    Not rated yet
    • $23.55
    • Including 20% UK VAT*
  • RS485 Click Board™ 5V

    The RS-485 5V Click Board™ is a compact accessory board designed to add bidirectional data communication to the design. The board features a Texas Instruments ADM485 differential line transceiver that provides high-speed bidirectional data communication on multipoint bus transmission lines. Compliant with EIA standards RS-485 and RS-422, this 5V version of RS485 Click Board™ is intended for balanced data transmission. RS485 Click Board™ 5V board features four screw terminals. The two terminals marked with.

    Not rated yet
    • $23.55
    • Including 20% UK VAT*
  • RS485 Isolator 2 Click Board™

    The RS485 Isolator 2 Click Board™ features ADM2867E a 5.7 kV rms signal and power isolated full duplex RS-485 transceiver. The device also features cable invert pins, allowing the user to quickly correct reversed cable connection on A, B, Y, and Z bus pins while maintaining receiver full receiver fail-safe performance. This full duplex device allows for independent cable inversion of the driver and receiver for additional flexibility with high speed 25 Mbps data rate.

    RS485 Isolator 2 Click Board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click Board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $37.94
    • Including 20% UK VAT*
  • RS485 Isolator Click Board™

    The RS-485 Isolator Click Board™ is a RS485 communication isolator, and carries the ADM2682EBRIZ, a 5 kV rms signal and power isolated RS-485 transceiver.

    The Click Board™ is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface, with additional functionality provided by the RST and CS pin on the MikroBUSline.

    Not rated yet
    • $64.11
    • Including 20% UK VAT*

Bestsellers

* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.