Storage Device Click Boards™

Products: 116 of 28
  • Dual EE Click Board™

    The Dual EE Click Board™ contains two AT24CM02 EEPROM ICs onboard which gives total of 4MB of memory. Each memory IC can be addressed through the I2C interface with the transfer speed of 400KHz. This Click board™ offers any kind of temporary or permanent data storage for various. embedded electronic devices, as well as simple data logging or even storing various working parameters of a certain module or device. It can also safeguard all of the sensitive data in case of a particular power cycle and it has many other capabilities.

    Dual EE click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $19.35
    • Including 20% UK VAT*
  • EEPROM 2 Click Board™

    The EEPROM 2 Click Board™ carries ST's M95M02-DR DIP-8 socket EEPROM chip with 256 KB of memory. The chip has byte and page write speeds equal or less than 10 ms.

    Not rated yet
    • $19.35
    • Including 20% UK VAT*
  • EEPROM 3 Click Board™

    The EEPROM 3 Click Board™ provides 2 Mbit (2,097,152 bits) of Electrically Erasable Programmable Read Only Memory, organized in bytes. In other words, this Click Board™ is an EEPROM memory medium with the capacity of 256 KB. The used EEPROM module has outstanding endurance, with 1,000,000 write cycles and data retention period of over 100 years. The EEPROM module on this Click Board™ features Schmitt trigger inputs for better noise protection, self-timed write cycles, it has a dedicated write protect pin for hardware protection of stored data, and error detection and correction logic scheme that ensures reliable data output, staying transparent to the host controller.

    Not rated yet
    • $15.05
    • Including 20% UK VAT*
  • EEPROM 4 Click Board™

    The EEPROM 4 Click Board™ is 2,097,152 bits on a Click Board™, organized into 262,144 bytes. In other words, this Click Board™ is an EEPROM memory medium with the capacity of 256 KB. The used EEPROM module has very good endurance and it can withstand 1,000,000 write cycles, with the data retaining period of about 40 years. The EEPROM module on this Click Board™ can work with power supply voltage ranging from 1.7V to 5.5V, it features the self-timed write cycles, doesn't require erase before writing, has a dedicated write protect pin for hardware protection of stored data, and has a dedicated hold pin used for holding the data transfer.

    Not rated yet
    • $16.12
    • Including 20% UK VAT*
  • EEPROM 6 Click Board™

    The EEPROM 6 Click Board™ is a compact add-on board that contains a serial EEPROM memory that operates from the 1-Wire interface. This board features the DS28EC20, a 20480-bit EEPROM organized as 80 memory pages of 256 bits each from Maxim Integrated. As a specific feature, blocks of eight memory pages can be write-protected or put in “EPROM-Emulation” Mode, where bits can only be changed from a 1 to a 0 state. It communicates with MCU at 15.4kbps or 90kbps over the 1-Wire protocol and has a 64-bit registration number that ensures error-free device selection. This Click board™ is suitable for applications like device authentication, data for self-configuration of central office switches, wireless base stations, or other modular-based rack systems.

    EEPROM 6 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $9.67
    • Including 20% UK VAT*
  • EEPROM Click Board™

    The EEPROM Click Board™ from MikroE is an add-on storage board that includes a 24C08WP serial EEPROM with 8 Kbits of memory. Driven by CMOS technology, this Click Board™ enables the user to add more 8 Kbit EEPROM memory to the device. An ideal choice for low power and low voltage applications, 24C08WP module is compatible with the I2C memory standard and uses a bi-directional data bus and serial clock. It is available in a DIP packaging. The DIP socket makes EEPROM easily replaceable. EEPROM Click Board™ works well with both the 100 kHz I2C standard-mode and the 400 kHz I2C fast-mode. The board is designed to operate on 3.3V or 5V power supply, selectable by an SMD jumper. Another set of SMD jumpers that allow address selection are also available on the board. The green LED diode denotes the status of power supply.

    The EEPROM Click Board™ is an ideal selection for storing initialisation and configuration data of your device.

    Not rated yet
    • $8.60
    • Including 20% UK VAT*
  • EERAM 2 Click Board™

    The EERAM 2 Click Board™ is a standalone serial SRAM memory that includes shadow non-volatile backup. EERAM uses a small external capacitor to provide the energy needed to move the contents of the SRAM to the non-volatile cells when system power is lost. Unlike NVSRAM, no external battery is needed. EERAM offers unlimited SRAM read and write cycles and more than 100,000 backups to the non-volatile cells. 

    Since power loss events are typically random or unpredictable, EERAM works in applications that absolutely cannot lose the quickly changing SRAM data on any sudden power loss. It provides designers of a data logging/black box or monitoring systems with a safe and accurate way to safely, reliably and automatically store the last data bytes prior to the power loss event. The Vcc is monitored inside the IC and can automatically handle the data movement between the SRAM and the non-volatile memory on any power disruption. 

    Not rated yet
    • $15.05
    • Including 20% UK VAT*
  • EERAM 3.3V Click Board™

    Add memory to your project with EERAM 3.3V Click Board™. It carries the 47L16 EERAM, a 16Kbit SRAM with EEPROM Backup from Microchip. The Click Board™ is designed to run on a 3.3V power supply. It communicates with the target microcontroller over I2C interface, with additional functionality provided by the INT pin on the MikroBUS line.

    Not rated yet
    • $15.05
    • Including 20% UK VAT*
  • EERAM 5V Click Board™

    Add memory to your project with EERAM 5V Click Board™. It carries the 47C16 EERAM, a 16Kbit SRAM with EEPROM Backup from Microchip. The Click Board™ is designed to run on a 5V power supply. It communicates with the target microcontroller over I2C interface, with additional functionality provided by the INT pin on the MikroBUS line.

    Not rated yet
    • $15.05
    • Including 20% UK VAT*
  • Flash 2 Click Board™

    The Flash 2 Click Board™ features a 64 Mbit Flash memory IC, manufactured by using the proprietary high-performance CMOS Super-Flash' technology, which allows the Flash 2 Click Board™ to withstand up to 100,000 write cycles, with the data retention period of 100 years, which is considerably longer than any other memory module of this type. The flash memory IC used on this Click Board™ features Serial Flash Discoverable Parameters (SFDP) mode, used to retrieve the advanced information from the device, such as the operating characteristics, structure and vendor specified information, memory size, operating voltage, timing information, and more.

    Not rated yet
    • $12.90
    • Including 20% UK VAT*
  • Flash 3 Click Board™

    Flash 3 Click Board™ is a mikroBUS add-on board for adding more Flash Memory to your target board microcontroller. It carries an ISSI IS25LP128 IC with 128 Mbit capacity.

    Not rated yet
    • $12.90
    • Including 20% UK VAT*
  • Flash 4 Click Board™

    The Flash 4 Click Board™ is a perfect solution for the mass storage option in various embedded applications. With fast performance being one of its key features, Flash 4 Click Board™ can also be used for the code shadowing, execute-in-place (XIP), and data storage. It features the S25FL512S Flash memory module made by combined high-performance MirrorBit technology and Eclipse architecture. The 512Mbit SPI Flash memory module is one of the fastest and most reliable Flash modules on the market.

    It comes in the package which also includes the mikroSDK software and a library with all the functions. The Click Board™ comes as a fully tested and approved prototype, making it a reliable device ready to use on the development board.

    Not rated yet
    • $26.87
    • Including 20% UK VAT*
  • Flash 5 Click Board™

    The Flash 5 Click Board™ is a perfect solution for the mass storage option in various embedded applications. It features the W25N01GVZEIG/IT (1G-bit) Serial SLC NAND Flash Memory from Winbond which provides a storage solution for systems with limited space, pins and power. The W25N SpiFlash family incorporates the popular SPI interface and the traditional large NAND non-volatile memory space. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP) and storing voice, text and data.

    The Flash 5 click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $9.67
    • Including 20% UK VAT*
  • Flash 6 Click Board™

    The Flash 6 Click Board™ based on the W25Q128JV (128M-bit) flash memory from Winbond provides a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP) and storing voice, text and data. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage.

    The Flash 6 click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

    Not rated yet
    • $7.52
    • Including 20% UK VAT*
  • Flash Click Board™

    Introduce additional flash memory to the design with the Flash Click Board™. This small accessory board offers an easy and reliable solution for externally storing large amounts of data to be used in the project. The board features an EN25F80 8 megabit serial flash memory with uniform 4 Kbytes sector architecture. Designed for applications that need high performance and low power consumption, it supports clock frequency up to 75 MHz. EN25F80 module comes with software and hardware Write protection that enable the user to Write Protect all or portion of memory via software. The memory is divided into 16 sectors, each containing 256 pages; each page is 256 bytes wide. Flash Click Board™ communicates with the target board microcontroller through SPI interface. The board is designed to use 3.3V power supply only. The green LED diode denotes the power supply status.

    Flash Click Board™ is an ideal choice for a mass storage option in multimedia devices, drives, optical and printing devices.

    Not rated yet
    • $10.75
    • Including 20% UK VAT*
  • FRAM 2 Click Board™

    Additional memory for your next project!.

    The FRAM 2 Click Board™ carries the CY15B104Q 4-Mbit(512K x 8) serial F-RAM from Cypress. A ferroelectric random-access memory or F-RAM is non-volatile and performs reads and writes similar to a SRAM. You can access the memory using an industry-standard serial peripheral interface (SPI) bus.On the functional level, the F-RAM operates in a similar way as serial flash and serial EEPROMs. The major difference between the CY15B104Q and a serial flash or EEPROM with the same pinout is the F-RAM's superior write performance, high endurance, and low power consumption.

    Not rated yet
    • $20.42
    • Including 20% UK VAT*
Products: 116 of 28

Bestsellers

* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.