HMI Click Boards

Products: 116 of 48
  • 2x2 Key Click Board™

    The 2x2 Key Switch Click Board™ has a 4 button keypad. The Click Board™ allows multiple key presses and has a debounce circuit composed of 74HC32 quad 2-input OR gate from NXP and the SN74HC14 Hex Schmitt-Trigger Inverter from Texas Instruments. 2x2 Key Click Board™ is designed to use either 3.3V or 5V power supply. The buttons can be independently read.

    Not rated yet
    • $11.36
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • 4x4 Key Click Board™

    4x4 Key Click Board™

    Not rated yet
    • $13.89
    • Including 20% UK VAT*
    Only 4 left in stock. Order Now
  • 4x4 Key Click Board™ Plus

    The 4x4 Key Click Board™ from MikroE is a standardized compact add-on board featuring a densely packed 16 button DTMF keypad and two 8-bit shift registers. It is designed to connect a 4x4 matrix keypad to a microcontroller or microprocessor without using too many I/Os. All the inputs made on the 4x4 keypad are processed by a pair of serially connected 8-bit parallel-in serial-out shift registers.

    The keypad is also capable of registering multiple key presses at the same time. It is compatible with all MikroElektronika compilers.

    Not rated yet
    • $13.89
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Analog Key Click Board™

    The Analog Key Click Board™ is an analog keyboard on a Click Board™. It contains six tactile push-buttons, used to select one of six different voltage levels. The idea behind this Click Board™ is very simple: six resistors form a voltage divider. The resistors are connected in series between the VCC and the GND. Each button selects one of the six middle taps, allowing six different voltage levels to be selected. The voltage is available at the AN pin of the mikroBUS, which is additionally protected by an operational amplifier, configured as a buffer. This allows both protection and a proper impedance at the analog input pin of the microcontroller.

    Not rated yet
    • $17.67
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Button Alarm Click Board™

    Button Alarm Click Board™

    Not rated yet
    • $26.51
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Button G Click Board™

    Add a simple pushbutton functionality to your design with the Button G Click Board™. While the user has a freedom to choose from a range of onscreen user interfaces, the tactile feedback from pushing a physical button is hard to replace. The user can set it up depending on the device/design requirement. Any application that user a user-interface design and requires the tactile feel and feedback of a hardware pushbutton, Button G Click Board™ seems to be an ideal choice. On press, the button is designed to send an interrupt signal to the target board microcontroller. The initial.

    Not rated yet
    • $12.50
    • Including 20% UK VAT*
  • Button PLAY Click Board™

    The Button PLAY Click Board™ is a very interesting interactive gadget on a Click Board™. It is an integrated capacitive touch sensor display in the form of a button. By utilising an advanced capacitive touch sensing technology, the CTHS15CIC05ARROW sensor can successfully replace the traditional mechanical button, allowing very simplified yet reliable user interfaces to be developed. Besides the touch detection, this sensor also features a green arrow icon with backlight, which makes the Click Board™ very useful for building various stylized and visually appealing interfaces.

    Not rated yet
    • $26.51
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Button Power Click Board™

    Button Power Click Board™

    Not rated yet
    • $23.98
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Button R Click Board™

    Add a simple pushbutton functionality to your design with the Button R Click Board™ from MikroE. While the user has a freedom to choose from a range of onscreen user interfaces, the tactile feedback from pushing a physical button is hard to replace. The user can set it up depending on the device/design requirement. Any application that user a user-interface design and requires the tactile feel and feedback of a hardware pushbutton, Button R Click Board™ seems to be an ideal choice. On press, the button is designed to send an interrupt signal to the target board microcontroller.

    Not rated yet
    • $12.50
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Button Y Click Board™

    Button Y Click Board™ is a Click Board™ equipped with the tactile switch, sometimes referred to as a pushbutton. A pushbutton is a component that is used very often in various designs, allowing the user to interact with the application. Although it sounds simple, a button needs to comply with a range of application requirements. It needs to have a very good mechanical endurance while retaining its specifications, a predictable bouncing time, a very low ON resistance, very high OFF resistance, and it needs to fulfill aesthetical requirements.

    It comes in the package which also includes the mikroSDK software and a library with all the functions. The Click Board™ comes as a fully tested and approved prototype, making it a reliable device ready to use on the development board.

    Not rated yet
    • $12.50
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Buzz 2 Click Board™

    The BUZZ 2 Click Board™ carries the CMT-8540S-SMT magnetic buzzer transducer.

    The buzzer's resonant frequency is 4kHz. The Click Board™ is designed to run on either 3.3V or 5V power supply.

    Not rated yet
    • $15.15
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Buzz Click Board™

    Add sound function to the device in the form of beeps, tones and alerts using the Buzz Click Board. This audio and voice board employs a premium piezo speaker that produces audio signals. This compact round speaker allows the user to create simple audio sounds or voice messages into portable devices. The piezo speaker/buzzer is designed for best performance with a resonant frequency of 3.8 kHz. The Buzz Click Board™ also features an integrated buzzer driver is connected to either the digital (CS/GPI) or the PWM line. Either of these pins can be used to provide the signal from the MCU to the buzzer driver. This Click Board™ is designed to operate using a 5V power supply. The user can solder an SMD jumper to the 3.3V position, when required. It has on-board power LED that denotes the power status.

    Buzz Click Board™ is an ideal choice for introducing audio signalization functionality to any user device.

    Not rated yet
    • $11.36
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Camera Click Board™

    The Camera Click Board™ is a popular add-on board that allows user to see the world through the eye of an OV767-VL2A low voltage CMOS image sensor. The sensor is connected to an on-board FT900 MCU via a parallel camera interface, which in turn, outputs the camera image to the target board through the MikroBUS SPI interface (CS, SCK, MISO, MOSI).

    Not rated yet
    • $44.18
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Cap Extend 3 Click Board™

    The Cap Extend 3 Click Board™ features four capacitive sensor pads integrated on the PCB, that can sense touch through a variety of different materials. This Click Board™ can sense touch through plastic, wood, or even metal, thanks to the proprietary Metal over Capacitive technology. All these materials can be used to protect the surface of the PCB and sensor pad traces, allowing implementation of all kinds of human-machine interfaces and seamless integration of the touch-sensitive buttons into various kinds of front panels. The Click Board™ also features a connector used for connecting to external sensors.

    Not rated yet
    • $18.93
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Cap Extend Click Board™

    Cap Extend Click Board™ carries a SEMTECH SX8633 low power, capacitive button touch controller. It has 12 pins for connecting capacitive inputs (either touch-buttons or proximity sensors). Any sort of conductive object can be used as an input.

    Not rated yet
    • $22.72
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
  • Cap Slider 2 Click Board™

    Cap Slider 2 Click Board™

    Not rated yet
    • $18.93
    • Including 20% UK VAT*
    Only 1 left in stock. Order Now
Products: 116 of 48

Bestsellers

* Note: VAT registered customers in the EU (except UK) and all customers outside the EU will have VAT deducted at the checkout.