The cookie settings on this website are adjusted to allow all cookies so that you have the very best experience. If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the account menu. 
    
 

LED Display Click Boards

LED Display Click Boards


Products

16x12 G Click Board

The 16x12 G Click Board carries a 16x12 LED display and the IS31FL3733 matrix driver. The click is designed to run on either 3.3V or 5V power supply.

It communicates with the target microcontroller over I2C interface, and the following pins on the MikroBUS line: INT, RST, CS. .

MIKROE-2758

£36.00

16x9 G Click Board

The 16x9 G Click Board contains a green LED matrix and the IS31FL3731 audio modulated matrix LED driver.

The dimension of the LED matrix is 16x9. Each LED can be controlled individually both for on/off control and light intensity.

The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over I2C interface.

MIKROE-2520

£40.80

4D-display Click Board

4D - display click is an adapter Click board™ that offers a mikroBUS™ interface for controlling 4D Systems gen4 Series intelligent Display Modules. 4D Systems designs and manufactures a wide range of Intelligent Display Modules equipped with powerful graphics processors. Their displays allow graphical objects control by exchanging specifically formatted messages with the external microcontroller (MCU) over the UART. By utilizing the 4D - display click, it is possible to develop an MCU firmware application that can interact with the graphic objects on the 4D Intelligent Display Module over the mikroBUS™. This significantly simplifies the application design, while reducing the processing load on the host MCU, allowing amazing graphically based applications to be created, even with slower 8bit MCUs.

MIKROE-3044

£10.80

4Dot Matrix R Click Board

The 4Dot-Matrix R Click Board allows you to display 4 characters of 5x7 dot size. The click is designed to run on either 3.3V or 5V power supply.

It communicates with the target microcontroller over I2C interface, with additional functionality provided by the following pins on the MikroBUS line: RST, CS, PWM.

MIKROE-2706

£50.57

4X4 RGB Click Board

The 4x4 RGB Click Board is an add-on board which helps the user to add a colourful RGB LED matrix to the design. This accessory board comes equipped with a matrix of 16 very bright WS2812 RGB LEDs and a MCP1826 low dropout regulator. Each of these 16 LEDs further comprises of three single coloured LEDs (Red, Green and Blue), and a control chip. Put together, there are a total of 48 individual LEDs in 4x4 RGB click board. The control circuit and RGB chip have been integrated in a package of 5050 components to keep pixel point in complete control. 4x4 RGB click features a jumper (zero ohm resistor) for setting the I/O logic level. It is by default soldered in the 3.3V position but can make use of either a 3.3V or 5V power supply. The LED matrix is connected to the target board microcontroller through the MikroBUS RST pin.

4x4 RGB click can be used to create animations which can be scrolled on a computer screen. It is also usable for producing spellbinding displays of colourful graphics on electronic billboards, signs, and similar interfaces.


.


MIKROE-1881

£22.80

7-SEG RGB Click Board

The 7-SEG RGB Click Board carries a full colour single 7 segment digit display. The click is designed to run on either 3.3V or 5V power supply.

It communicates with the target microcontroller over the CS, and PWM pin on the MikroBUSline.

MIKROE-2734

£43.20

7seg Click Board

The 7seg Click Board is an accessory board that allows user to add 2-digit seven-segment display to the device. This compact board includes two on-board 74HC595 8-bit serial-in, parallel-out shift registers as well as two seven-segment displays. The 74HC595 shift register has an 8-bit storage register and an 8-bit shift register. The data is written to the shift register serially, then latched onto the storage register. The 7seg click uses the Serial Peripheral interface (SPI) to communicate with the target board microcontroller. The board is designed to operate using a 3.3V or 5V power supply, selectable by an SMD jumper. The power indicator LED is available on-board.

The 7seg click is an ideal choice for adding popular 7-segment display to the device while using only 4 microcontroller pins. The green LED diode denotes the status of the power supply.

MIKROE-1201

£12.00

7x10 B Click Board

The 7x10 B click is a LED dot matrix display click, which can be used to display graphics or letters in a very simple and easy way. The click board has two LED dot matrix modules with 7x5 stylish, round, dot-like LED elements.

These displays produce clean and uniform patterns since the elements are optically isolated from each other and there is no light bleeding between the adjacent LED cells. Additionally, turn-on and turn-off times of the matrix cells are optimized for a clean and fluid display performance, with no flickering or lag.

MIKROE-2789

£18.00

7x10 G Click Board

The 7x10 G Click Board can be used for displaying letters on a display with 7x5 font resolution. It carries a matrix of 70 green LEDs driven by a pair of 8-bit serial-in, parallel-out shift registers, a Darlington Transistor array and a Johnson counter.7x10 G click is designed to run on either 3.3V or 5V power supply.

It communicates with the target microcontroller over SPI interface, with additional functionality provided by the following pins on the MikroBUSline: AN, PWM, RST.

MIKROE-2705

£18.00

7x10 R Click Board

7x10 R click is a display add-on board that serves as an essential dual-character display capable of showing letters in more readable typefaces compared to a 14-segment display that supersedes the 7x5 standard resolution meant for displaying ASCII characters. The 7x10 R click is capable of carrying a matrix of 70 red LEDs driven by a pairs of 8-bit serial-in, parallel-out shift registers, a Darlington Transistor array and a Johnson counter. Apart from providing the user a dual- character display, the 7x10 R click also maintains the scope of providing four character display in case of doubling up on a board with two adjacent MikroBUS sockets, such as [clicker 2][3] or [Flip & click][2]. It is designed to use either a 3.3V or 5V power supply.

MIKROE-1993

£18.00

7x10 Y Click Board

The 7x10 Y Click Board is a LED dot matrix display click, which can be used to display graphics or letters in a very simple and easy way. The click board has two yellow LED dot matrix modules with 7x5 stylish, round, dot-like LED elements.

These displays produce clean and uniform patterns since the elements are optically isolated from each other and there is no light bleeding between the adjacent LED cells. Additionally, turn-on and turn-off times of the matrix cells are optimized for a clean and fluid display performance, with no flickering or lag.

MIKROE-2790

£18.00

8x8 B Click Board

Introduce a blue serial 8x8 LED matrix display to your design with the 8x8 B click. This display add-on board in the MikroBUS form factor incorporates an 8-digit MAX7219 LED display driver module as well as 64 (8x8) blue-coloured LEDs. This clock board is designed to communicate with the target board MCU through four MikroBUS SPI lines (DIN, DOUT, CLK and CS).

The serially-interfaced MAX7219 LED display driver features an on-chip BCD code-B decoder, digital and analog brightness control, and an 8x8 static RAM that stores each digit. 8x8 B click makes an ideal choice for bar graph displays, industrial controllers, led matrix displays, and panel meters. It is available in a range of other colour options including red, green, and yellow.

MIKROE-1307

£21.60