The cookie settings on this website are adjusted to allow all cookies so that you have the very best experience. If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the account menu. 
    
 

MikroE Click Boards

MikroE Click Boards

MikroE Click Boards

Click Boards™ offer simple and inexpensive way to evaluate and incorporate interfaces into your microntroller-based system. Over 185 different models have been created so far and the list grows weekly.


MikroBUS™

Developed by MikroElektronika (mikroE), Click Boards™ connect to your microcontroller via the MikroBUS™. a powerful interface common to all models. MikroBUS™ is evolving into a standard within the embedded systems market and is being taken up by many other manufacturers.

mikroBUS™ Pinout Diagram


Why Click Boards™?

They provide a standard way of adding evaluating new interface devices. MikroElektronika design and manufacture Click Boards™ for device manufacturers to offer a simple way of using their devices. They are compatible with all MikroE development boards, supporting a wide range of microcontroller types including ARM Cortex, AVR, PIC, PIC32, dsPIC, FT90x and 8051. MikroE models are also fully supported by MikroE complers and toolsets and example application code is created to enable you to start using your new Click Board™ straight away This can significantly reduce the learning curve normally associated with the introduction of new technology.

Incorporate MikroBUS™ into Your Own Design

There are many good reasons to want to offer extendability to your own board designs:

  • To allow other interfaces to be added to your own system without having to redesign your hardware.
  • Test the market for additional functionality at minimal outlay

Although mikroBUS™ is a trademark of mikroElektronika, they allow you to incorporate the bus layout into your design as long as the silkscreen is clearly labeled "mikroBUS™" and includes the mikroBUS™ logo.


Third Party Support

Many leading semiconductor manufacturers are now offering MikroBUS™ interfaces on their development platforms allowing our models to be used wherever you need them.

New Arrivals

more...

Products

RTC 5 Click Board

NEW

RTC 5 Click Board

The mikroE RTC5 click is the fifth click board from Mikroelektronika carrying Microchip

MIKROE-1990

$28.51

RTC Click Board

NEW

RTC Click Board

The RTC Click is an accessory board designed to add time measuring functionality to the device. This click board has a PCF8583 serial real-time clock/calendar. The PCF8583 IC is a full binary-coded decimal (BCD) clock and calendar chip with 24- or 12-hour clock format with four-year calendar, based on a 2048-bit static CMOS RAM. For communication with the target board microcontroller, RTC Click uses the I2C interface. The board comes with an integrated 3V/230mA lithium battery that serves as a backup power supply. Even when the main power supply goes OFF, this backup power supply enables the device to function continuously. It is designed to use a 3.3V power supply, but can be used with 5V systems by soldering the PWR SEL SMD jumper to the 5V position.

RTC Click is an ideal choice for applications that require real-time clocks, calendars and programmed alarms.

MIKROE-947

$28.51

RTC6 Click Board

NEW

RTC6 Click Board

RTC6 Click Board

MIKROE-2063

$28.51

Shake2Wake Click Board

NEW

Shake2Wake Click Board

Introduce shake functionality to the device with the Shake2Wake click board. The board features two chips from Analog Devices: an ADXL362 accelerometer that includes several activity detection modes, which is connected to an ADP195 power switch IC. This power switch IC is in turn connected to a screw terminal for controlling external devices. Upon shaking, the accelerometer sends an interrupt to the switch, which in turn, powers up the external components. The intensity and duration of shaking required for waking it up is programmable, as well as the period of inactivity, which leads to switching off the external device. Shake2Wake click can also function as a regular accelerometer, wherein the board uses the mikroBUS SPI interface for communication to the target microcontroller. This click board is designed to operate using a 3.3V power supply only. Shake2Wake click works on two main operating modes:

MIKROE-1942

$47.18

SHT11 Click Board

NEW

SHT11 Click Board

Introduce digital humidity and temperature sensing capability to your device with the SHT11 Click Board. The board employs Sensirion

MIKROE-949

$30.10

SpeakUp Click Board

NEW

SpeakUp Click Board

The SpeakUp Click Board is a speech recognition click board that allows the user to set it up to recognize over 200 different voice commands. The board can be either plugged into a mikroBUS socket on a host microcontroller or used standalone, connecting directly to external devices.

The SpeakUp utility understands the user commands through a simple & straightforward process, irrespective of the language, dialect, or slang.

SpeakUp click incorporates a microphone, an audio IC and an STM32F415RG MCU with a DTW based firmware designed specifically for it. The DTW algorithm based firmware gives SpeakUp click its decision-making power and turns your talk into action

MIKROE-1534

$47.18

SRAM Click Board

NEW

SRAM Click Board

The mikroE SRAM click is a storage add-on board that carries the 23LC1024 IC, which allows the user to add 1Mbit of additional SRAM (static RAM) memory to the device. Based on low-power CMOS technology, the 23LC1024 chip outlines the memory in 8-bit instruction registers and 32-byte pages (128K x 8-bit). For Read and Write operations, this highly-reliable chip offers byte, page, and sequential operating modes. The sequential mode enables Read/Write operation for an entire memory array.

It supports unlimited Read/Write cycles to the memory array with zero Write time. It operates at a clock rate of 20 MHz for all the three Read/Write modes. Communicating through SPI-Compatible bus interface, the board also has an additional Hold pin functionality in place of the default RST pin. SRAM click can be used with either 3.3V or 5V power supply.

MIKROE-1902

$22.30

Stepper 2 Click Board

NEW

Stepper 2 Click Board

An improvement over its predecessor, the Stepper 2 click from mikroE is another addition in the range of motor driver click boards. Complete with an A4988 microstepping motor driver, Stepper 2 click surpasses the original Stepper click with an output drive capability of up to 35V and ??2A.

Not just power, the new version is designed to offer user more control (precision). It can go down to 1/16th of a step to drive the motor. The board features three pairs of onboard screw terminals for secure connectivity. The first two (2B, 2A; 1A, 1B) are for connecting the motor while the third pair (VIN and GND) is for an external power supply (minimum 7V).

Stepper 2 click is intended to operate bipolar stepper motors in full-, half-, quarter-, eighth-, and sixteenth-step modes. The user can select between the different stepping modes (steps and micro steps) using a set of three (J1-J3) onboard jumpers. Stepper 2 click uses mikroBUS EN, RST, SL, ST and DIR pins to communicate with the target board microcontroller. It is designed to work with 3.3V power supply but is also compatible with 5V logic level.

MIKROE-1926

$26.45

STEPPER Click Board

NEW

STEPPER Click Board

Introduce precision motor control to the user device with STEPPER click board. This stepper motor driver board includes an A3967SLBT stepper motor driver that allows controlling bipolar step motors in full-, half-, quarter- and eighth-step modes. The maximum output drive capability is 30V and nearly ??500 mA.

It also features an integrated translator that supports easy implementation of the A3967SLBT microstepping driver. The package is offered with two sets of connectors: a B5B-XH-A connector and a pair of screw terminals. Both the types of connectors are delivered unsoldered with the package and can be used as a connecting option. The user can use the j3 jumper to select whether the power of the motor driver comes with the on-board or external power supply. STEPPER click supports either a 3.3V or 5V power supply, which can be selected through the zero-ohm J1 SMD jumper (3.3V is the default position). The user can also choose to use the motor driver

MIKROE-1528

$25.41

STM32 M4 Clicker Board

NEW

STM32 M4 Clicker Board

STM32 M4 Clicker Board

MIKROE-1675

$32.66

Temperature & Humidity Click Board

NEW

Temperature & Humidity Click Board

The MikroE Temp&Hum click is a fully calibrated temperature and humidity click board equipped with ST

MIKROE-1971

$23.33

Thermo 2 Click Board

NEW

Thermo 2 Click Board

THERMO 2 click is a measurement accessory board that includes DS1825, a programmable resolution 1-wire digital thermometer. The digital thermometer provides 9 to 12-bit centigrade temperature measurements and communicates over a 1-Wire bus. The DS1825 chip has a unique 64-bit serial code, which allows the user to connect multiple DS1825s to function on the same 1-Wire bus.

THERMO 2 click has a measuring range between

MIKROE-1840

$22.30