The cookie settings on this website are adjusted to allow all cookies so that you have the very best experience. If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the account menu. 
    
 

MikroE Click Boards

MikroE Click Boards

MikroE Click Boards

Click Boards™ offer simple and inexpensive way to evaluate and incorporate interfaces into your microntroller-based system. Over 185 different models have been created so far and the list grows weekly.


MikroBUS™

Developed by MikroElektronika (mikroE), Click Boards™ connect to your microcontroller via the MikroBUS™. a powerful interface common to all models. MikroBUS™ is evolving into a standard within the embedded systems market and is being taken up by many other manufacturers.

mikroBUS™ Pinout Diagram


Why Click Boards™?

They provide a standard way of adding evaluating new interface devices. MikroElektronika design and manufacture Click Boards™ for device manufacturers to offer a simple way of using their devices. They are compatible with all MikroE development boards, supporting a wide range of microcontroller types including ARM Cortex, AVR, PIC, PIC32, dsPIC, FT90x and 8051. MikroE models are also fully supported by MikroE complers and toolsets and example application code is created to enable you to start using your new Click Board™ straight away This can significantly reduce the learning curve normally associated with the introduction of new technology.

Incorporate MikroBUS™ into Your Own Design

There are many good reasons to want to offer extendability to your own board designs:

  • To allow other interfaces to be added to your own system without having to redesign your hardware.
  • Test the market for additional functionality at minimal outlay

Although mikroBUS™ is a trademark of mikroElektronika, they allow you to incorporate the bus layout into your design as long as the silkscreen is clearly labeled "mikroBUS™" and includes the mikroBUS™ logo.


Third Party Support

Many leading semiconductor manufacturers are now offering MikroBUS™ interfaces on their development platforms allowing our models to be used wherever you need them.

New Arrivals

more...

Products

Thermo 3 Click Board

NEW

Thermo 3 Click Board

The mikroE Thermo 3 click is a temperature measurement board that incorporates an ultra-compact TMP102 IC from Texas Instruments. TMP102 chip works as a digital temperature sensor and is ideal for applications where high accuracy is required. It provides accuracy of ??0.5??C without requiring calibration. Offered in a tiny footprint of 1.6-mm ?

MIKROE-1885

$16.07

Thermo Click Board

NEW

Thermo Click Board

The THERMO Click Board is a compact accessory board that employs a MAX31855K thermocouple-to-digital converter. It performs cold-junction compensation, resolves temperatures to 0.25??C, and allows readings as high as +1372??C and as low as -270??C. It has a sensitivity of about 41?

MIKROE-1197

$36.81

THUMBSTICK Click Board

NEW

THUMBSTICK Click Board

Thumbstick click is a quality input board that makes it easy for the users to add a high precision analog thumb joystick to their design. This click board features a MCP3204 12-bit A/D converter. It also has got a pushbutton enabled joystick with dual axis and spring return. This joystick is quite similar to the ones used on joypads on popular gaming consoles like PS2 and Xbox controllers. Thumbstick click has typical life span of 100,000 cycles. With the help of two potentiometers connected to a stick, directional input gets received in the x and y axes of the joystick unit. An interrupt signal to the target board microcontroller is sent by the mechanical pushbutton. The MCP3204 12-bit A/D converter then converts the analog signal to digital. To output this digital signal to the target board, Thumbstick click makes use of mikroBUS SPI (CS, SCK, MISO and MOSI) lines.

Thumbstick click Input device is suitable for fine control of graphical user interfaces and remote control operated video games, since it facilitates 360 degree directional movement.

MIKROE-1627

$27.47

Thunder Click Board

NEW

Thunder Click Board

Add a lightning sensor to the design with the Thunder click. This add-on measurement board incorporates AS3935 Franklin lightning detector IC and MA5532 coil antenna.

For communication with the target board microcontroller, Thunder click uses the mikroBUS SPI (MOSI, MISO, SCK, CS) and INT lines. The board is designed to use 3.3V or 5V power supply, selectable via SMD jumper.

Thunder click is designed to detect the existence and proximity of potentially hazardous lightning activity within a 40km radius. Thunder click is also capable of providing an estimation of the distance to the head of the storm from 40km away down to 1km in 14 steps, while rejecting disturbances from man-made signals, such as motors and microwave ovens. It can also provide information on the noise level, which makes it an ideal choice for weather stations, sports equipment, UPS, power line conditioners, smart grid systems, environmental monitoring systems, portable GPS, bike computers, etc.Thunder click provides detection of both cloud-to-ground and cloud-to-cloud lightning activity within a 40km range.


MIKROE-1444

$43.03

Tilt Click Board

NEW

Tilt Click Board

The Tilt Click Board from mikroE is a measurement click board that includes RPI-1035, a four-directional optical tilt sensor. This surface mount type optical sensor provides positional feedback by telling if the device is leaning left, right, forward or backward at a given moment. It also offers substantial benefits over mechanical or magnetic-based direction detector solutions, which also makes it an ideal solution for situations where the user only require direction detection, and not the highly precise positional measurements. Tilt click communicates with the target board MCU through mikroBUS PWM and INT lines to get Vout1 and Vout2 outputs from the sensor. It also has two onboard LED signals that are responsible for visual feedback from the sensor. The click board uses either a 3.3V or 5V power supply.

It is ideal for remote controls or game controllers, as well as applications related to robotics, or rotating displays.

MIKROE-1834

$20.11

TILT n SHAKE Click Board

NEW

TILT n SHAKE Click Board

The mikroE TILT-n-SHAKE click is a multifunctional add-on board that is designed to keep away people from tampering with your design. Featuring a combination of tilt AND shake functionalities, the TILT-n-SHAKE click includes a MMA8491Q IC sensor that is used as a 3-axis, 45-degree tilt sensor and can also be configured as a 3-axis digital accelerometer. The user is required to keep the Enable pin (EN) pulled to logic level high to use it as an accelerometer.

Featuring a 14-bit digital output and ??8g full-scale range, this MEMS chip has a 1 mg/LSB sensitivity, and a fast response time of around 700 microseconds. TILT-n-SHAKE click communicates with the target board MCU through mikroBUS I2C interface, using SCL, SDA pins. As a tilt sensor, the MMA8491Q chip has three detection outputs, one for each axis: Xout, Yout and Zout. For specific applications you may need only one or two dimensions, not all three.

This click board is intended to use a 3.3V power supply. It is ideal for tamper detect and anti-theft detection systems.

MIKROE-1853

$26.45

TouchKey Click Board

NEW

TouchKey Click Board

The TouchKey Click features four capacitive pads powered by the TTP224 touchpad detector IC. TTP224 chip comes with multiple operating modes that allow the user to configure how the buttons will work. The capacitive pads can be toggled even when placed under a layer of glass or paper. TouchKey Click outputs four interrupt signals: OUTA, OUTB, OUTC and OUTD in place of default mikroBUS RST, AN, PWM and INT pins, respectively. It features three onboard jumpers enable the user to configure several operating modes of the TTP224 IC, including fast mode or low power mode, direct or toggle mode, enable/disable multi-key input, and so on. TouchKey Click is designed to work on either 3.3V or 5V power supply.

It works as an ideal replacement for mechanical switches and buttons, and being capacitive, it can register inputs through paper or glass.

MIKROE-1906

$19.18

TouchPad Click Board

NEW

TouchPad Click Board

Introduce an input device to the prototype using the Touchpad Click Board from mikroE. With a small form factor, this click board acts as a minimalistic capacitive touch input device powered by Microchip

MIKROE-1995

$22.30

tRF Click Board

NEW

tRF Click Board

tRF click is an RF communication board featuring the Telit LE70-868 wireless transceiver module. Along with the LE70-868 short range module, the board incorporates an SMA connector for an antenna, two radio communication LEDs, and a mikroBUS connector. Telit LE70-868 is an 868 MHz transceiver module with an embedded stack that is easy to integrate and use in point-to-point or star network topologies.

tRF click enables radio data rates from 4.8 to 57.6 kbps with maximum output power of 500mW, and features a wireless range of up to 10km in line-of-sight. However, this is the case for ideal conditions with no barriers to disrupt the signal. The user can still achieve a range of over 4km in open space under mixed conditions.

The tRF click board also includes two radio LEDS: transmit (red) and receive (yellow). It uses mikroBUS UART (Rx, Tx), AN, RST, PWM and INT lines for communication with the target board MCU. tRF click is intended to use a 3.3V power supply only.

MIKROE-1535

$67.91

Uni Hall Click Board

NEW

Uni Hall Click Board

After the BI HALL click, a new click also based on the Hall effect: the UNI HALL Click Board from mikroE. It offers the user an easy way to introduce a unipolar Hall switch to the design. The board is equipped with the Melexis US5881 unipolar Hall-effect sensor that is sensitive to north pole magnetic fields. It outputs a LOW logic level when exposed to a north-pole magnetic field, whereas a HIGH logic level when the north pole is taken away or a south pole is introduced. UNI HALL click also features a 74LVC1T45 single-bit, dual supply translating transceiver. The board uses mikroBUS INT line for communication with the target board microcontroller. It is designed to use either a 3.3V or 5V power supply, which is selectable through a solder jumper.

UNI HALL click can be utilized in countless ways by placing magnets in strategic spots. It is an ideal option to make durable push buttons, or regulate RPM by mounting it on a wheel, or detecting liquid level by attaching it to a float. In its simplest application, UNI HALL click can be engaged as part of a durable contactless proximity switch.

MIKROE-1647

$19.18

Unique ID Click Board

NEW

Unique ID Click Board

Unique ID click is a low-cost accessory board that includes a DS2401 enhanced Silicon Serial Number IC. It provides a unique registration number to the hardware design. Two Unique ID clicks might look alike on the outside, but each click board features a unique 48-bit serial number, which distinctively identifies the device in the world of mass-produced electronics. Unique ID click is also an excellent teaching tool for a user to understand how 1-Wire communications work. It uses 1-Wire interface for communication with the target board microcontroller, either through a GP1 or GP0 pin (here in place of the default AN and PWM mikroBUS pins). The power for reading/writing the device is derived from the data line itself with no need for an external power source. The multidrop capability also allows for multiple DS2401 chips to reside on a single data line. It is designed to use either a 3.3V or 5V power supply.

Unique ID click is an ideal choice for equipment registration, PCB identification, to establish network node ID, and other similar purposes.

MIKROE-1819

$16.07

USB I2C Click Board

NEW

USB I2C Click Board

The mikroE USB I2C click is a communication add-on board that acts like a highway intersection with one way in, three ways out for serial data. It incorporates a Microchip

MIKROE-1985

$21.15