The cookie settings on this website are adjusted to allow all cookies so that you have the very best experience. If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the account menu. 
    
 

MikroE Interface

MikroE Interface


Products

EasyBluetooth Board

EasyBluetooth Board

The EasyBluetooth is an add-on board that is designed to integrate wireless capability to the device. Featuring onboard fully qualified RN41 Bluetooth 2.1/2.0/1.2/1.1 module, this accessory board operates on low power and high data rates. The RN41 module provides support for multiple internet protocols and enables simple integration. For communication with the host microcontroller, the board uses UART interface. The EasyBluetooth board features six specialized connection pads on the side of the board. These connection pads allow for easy connection to the USB-UART board and control it through a PC as a standalone Bluetooth device, which also eliminates the need to use the microcontroller. The board includes a female IDC10 connector to plug it into a development system.

The EasyBluetooth board can use both 3.3V and 5V power supply.

This high performance RN41 delivers up to a 3-Mbps data rate for distances up to 100 meters. It makes a highly economic alternative to add wireless ability to the device without spending substantial time and money in the development of Bluetooth-specific hardware and software.

MIKROE-641

$53.74

EasyBuzz Board

EasyBuzz Board

The EasyBuzz Board is an accessory board featuring a piezo buzzer capable of emitting audio signals. It is required to generate a voltage signal of specified frequency in order to operate the piezo buzzer normally. The onboard piezo speaker is capable of playing sound frequencies in the range between 20 Hz and 20 kHz. However, the resonant frequency of piezo speaker is 3.8 kHz and the best sound quality is achieved using frequencies between 2 kHz and 4 kHz. A DIP switch further aids in configuring board connections. The buzzer driver can be provided with a digital signal or a pulse-width modulated signal, where sound pitch is regulated by the PWM frequency, and sound volume can be adjusted by changing the PWM duty cycle. It has a female IDC10 connector. The EasyBuzz Board supports both 3.3V and 5V systems.

With such features, the Piezo Speaker add-on board is an ideal choice for adding audio signalization to any prototype device.

MIKROE-478

$15.63

EasyConnect Board

EasyConnect Board

The EasyConnect Board is an accessory board that provides an easy access to the MCU pins via screw terminals. This additional board features on-board screw-terminated connectors that can handle solid and stranded wires. These connectors enable eight wires to be easily connected or removed. Featuring modular configuration, it permits several wires to be connected or removed with one operation. The EasyConnect Board has a female IDC10 connector that provides easy way to connect the peripheral devices to the development system. This additional board is designed to operate in a wide range of power supply range (from 2.7V to 5V). Featuring compatible headers already installed on MikroElektronika

MIKROE-128

$11.60

EasyConnect2 Board

EasyConnect2 Board

The EasyConnect2 Board is an accessory board that provides an easy access to the MCU pins via screw terminals. This additional board features on-board small screw-terminated connectors that can handle solid and stranded wires. These connectors enable eight wires to be easily connected or removed. Featuring modular configuration, it permits several wires to be connected or removed with one operation. The EasyConnect2 Board has a female IDC10 connector that provides easy way to connect the peripheral devices to the development system. This additional board is designed to operate in a wide range of power supply range (from 2.7V to 5V). Featuring compatible headers already installed on MikroElektronika

MIKROE-194

$11.60

EasyInput Board

EasyInput Board

Simulate different kinds of inputs in the design using the EasyInput Board. This accessory board is designed to provide digital logic input to desired IDC10 PORT header. The board comes equipped with a tri-state DIP switch for eight PORT pins. Popularly used in static input applications, the DIP switch provides user an easy and convenient way (simple push of a switch) to apply constant voltage (VCC or GND) on desired port inputs. The middle position leaves the pin unaffected.

The EasyInput Board has an IDC10 connector that ensures easy connection to peripheral modules. Also, this accessory board is most commonly used to customize the behavior of an electronic device to accommodate to wide range of applications.

MIKROE-1025

$12.51

EasyLED Board with Green LEDs

EasyLED Board with Green LEDs

Now easily add LED signals to the design using the EasyLED Board. The EasyLED Board is a cost-effective yet effective solution for visual indication of output signals. Featuring 8 surface mounted LEDs, the EasyLED Board is used to connect a development system port to LEDs. It features two IDC10 header connectors; one female header (CN2) and one male header (CN1). The user can connect a prototype device using its female IDC10 connector, or can be wired to your system using the make 2x5 pin header. These header connectors make EasyLED Board highly compatible with all development boards. The board supports 3.3V or 5V power supply voltage. This board is supplied with Green LEDs. Alternative boards are available fitted with red and yellow LEDs.

The EasyLED Board is used to indicate the logic level on the development system ports. When a pin is driven high (logic 1), the appropriate LED connected to that pin gets illuminated. Similarly, if a pin is driven low (logic 0), the appropriate LED remains off.

The user can use the EasyLED board with EasyPULL board in order to provide the device pin to VCC or GND via resistors and have visual indication of output signals via LED.

MIKROE-572

$15.43

EasyLED Board with Red LEDs

EasyLED Board with Red LEDs

Now easily add LED signals to the design using the EasyLED Board. The EasyLED Board is a cost-effective yet effective solution for visual indication of output signals. Featuring 8 surface mounted LEDs, the EasyLED Board is used to connect a development system port to LEDs. It features two IDC10 header connectors; one female header (CN2) and one male header (CN1). The user can connect a prototype device using its female IDC10 connector, or can be wired to your system using the make 2x5 pin header. These header connectors make EasyLED Board highly compatible with all development boards. The board supports 3.3V or 5V power supply voltage. This board is supplied with red LEDs. Alternative boards are available fitted with green and yellow LEDs.

The EasyLED Board is used to indicate the logic level on the development system ports. When a pin is driven high (logic 1), the appropriate LED connected to that pin gets illuminated. Similarly, if a pin is driven low (logic 0), the appropriate LED remains off.

The user can use the EasyLED board with EasyPULL board in order to provide the device pin to VCC or GND via resistors and have visual indication of output signals via LED.

MIKROE-571

$15.43

EasyLED Board with Yellow LEDs

EasyLED Board with Yellow LEDs

Now easily add LED signals to the design using the EasyLED Board. The EasyLED Board is a cost-effective yet effective solution for visual indication of output signals. Featuring 8 surface mounted LEDs, the EasyLED Board is used to connect a development system port to LEDs. It features two IDC10 header connectors; one female header (CN2) and one male header (CN1). The user can connect a prototype device using its female IDC10 connector, or can be wired to your system using the make 2x5 pin header. These header connectors make EasyLED Board highly compatible with all development boards. The board supports 3.3V or 5V power supply voltage. This board is supplied with Yellow LEDs. Alternative boards are available fitted with red and green LEDs.

The EasyLED Board is used to indicate the logic level on the development system ports. When a pin is driven high (logic 1), the appropriate LED connected to that pin gets illuminated. Similarly, if a pin is driven low (logic 0), the appropriate LED remains off.

The user can use the EasyLED board with EasyPULL board in order to provide the device pin to VCC or GND via resistors and have visual indication of output signals via LED.

MIKROE-573

$15.43

EasyPS/2 Board

EasyPS/2 Board

Introduce easy and fast PS/2 connectivity to the prototype or device using the EasyPS/2 Board. The EasyPS/2 board offers a direct connection between your microcontroller system and devices using PS/2 connectivity, such as PC, keyboard, a mice, or other input devices to a computer. For instance, the microcontroller can be linked either to a keyboard to capture pressed keys or to a PC to act as a keyboard or a mouse itself.

The EasyPS/2 board also includes a standard PS/2 connector in metal shield and a female IDC10 header for easy connection to the host system. Also, there are DIP switches that allow flexible configuration of the CLOCK and DATA lines. The clear marking on the board facilitates in secure and easy connections. The EasyPS/2 board is designed to operate using the 5V power supply only, according to the PS/2 standard specification.

MIKROE-486

$11.60

EasyTEST Board

EasyTEST Board

Now easily connect your prototype or development board to oscilloscope or other monitoring devices using the EasyTEST Board. It acts as a complete and cost-effective solution to deal with your connection problems. The simple adapter board has 10 port pins, labelled D0-D7, VCC, and GND. It splits a male 2x5-pin header into two 2x5-pin headers connected in parallel, with the same pinout as the original system

MIKROE-260

$12.61

EasyTFT Board

EasyTFT Board

Introduce advanced graphics functionality to the design using the EasyTFT Board that features a 2.83

MIKROE-1142

$41.84

EasyWiFi Board

EasyWiFi Board

Establish wireless communication between a microcontroller and a remote wireless device using the EasyWiFi board. Designed to be compatible with most microcontroller architectures, the EasyWiFi board is an all-in-one wireless 2.4GHz 802.11b solution with high-speed voltage translators. The board carries an MRF24WB0MA Wi-Fi radio transceiver module with integrated PCB antenna, matching circuitry, and supports Wi-Fi with the free TCP/IP protocol stack. It supports low-power, low data-rate Wi-Fi communication and communicates through 4-wire SPI and UART interface. The connection may be established via a flat cable with Mikroe development board-compatible IDC10 connectors on its ends. The board also has UART and JTAG pin pads available for testing purposes. It supports WEP, WPA-PSK, and WPA2-PSK security. It is designed to operate using both 3.3V and 5V power.

EasyWiFi Board is an ideal choice for industrial controls, home automation, building automation, and consumer applications.

MIKROE-574

$58.11