MicroElektronika (mikroE) is a dynamic forward thinking embedded systems development tools company with its headquarters in Belgrade.
MikroElekronika (MikroE) has chosen the Debug Store in the UK as their dedicated distributor of development tools.
The company is unique by producing complete development tool suites; ranging from compilers, debuggers, development platforms and training materials for a wide range of microcontroller families including ARM Cortex, AVR, PIC, PIC32, dsPIC and FT90x architectures. Support is also directly available for a huge range of peripheral devices including displays, video cameras, temperature probes and multi-axis gyroscopes and accelerometers by the provision of low-cost Click Modules. Their objective is to make the transition for the developer to a new architecture as simple and efficient as possible. It achieves this by providing software library support and working examples for all supported interfaces and development systems.
MikroElektronika (mikroE) have been chosen as the development tool company of choice by many major semiconductor manufacturers as they appreciate the use of mikroE tools will speed up development of new projects. They are recognised third-party development partners of companies such as Atmel, Cypress, Microchip, STMicroelectronics, Texas Instruments and official consultants to others including NXP.
DHT22 2 Click Board
The DHT22 2 Click Board is used for measuring the environmental temperature and relative humidity. It uses the CM2322 sensor, with very accurate thermal and humidity measuring capabilities. It can use either 1-Wire or I2C protocol to communicate with the integrated circuit.
Attributes like the ultra-small size, low power consumption, signal transmission distance up to 20 meters, make this sensor the perfect choice for all kinds of applications that require measurement of the temperature and humidity.
DHT22 Click Board
The DHT22 Click Board from Mikroelektronika is one of the simplest temperature and relative humidity sensor click board that carries the AM2302 sensor module, also known as DHT22. Concealed inside a plastic mesh packaging, the AM2302 temperature/humidity sensor needs just a single wire to communicate with the target board microcontroller.
For added convenience, DHT22 click is provided with two jumpers (zero ohm resistors). While one of them allows the user to choose between the MikroBUS pin to use (either CS or INT pin, which are SDA1 and SDA2 lines), the other on-board jumper allows the choice between 3.3V and 5V power supplies. The sensor generates the temperature/humidity data in a 16-bit resolution. The generated decimal number is 10 times the actual measurement, i.e., 216 would be 21.6
Diff pressure Click Board
The Diff Pressure Click Board carries NXP’s MPXV5010DP signal conditioned, temperature compensated and calibrated pressure sensor with two axial ports to accommodate industrial grade tubing. The click is designed to run either on 3.3V or 5V power supply. It communicates with the target microcontroller over SPI interface (CS, SCK, MISO).
Digi Pot 3 Click Board
The DIGI POT 3 Click Board is a versatile and feature-rich digital potentiometer click with 1024 steps and an internal non-volatile memory (EEMEM), which can be used for storing the wiper position, but also for storing various user data. The user EEMEM area has 14 words, each with 16bit length. The Click board™ can be used with both unipolar and bipolar signals, selectable by onboard SMD jumpers. The wiper position can be increased or decreased linearly or by the logarithmic scale (6db/step) with a single command. A special scratch register allows direct programming of the wiper position. It can be stored to the non-volatile memory and on the power on, it is automatically restored. This means that the device restores its last position after the power on - just like its mechanical counterpart.
DIGI POT 4 Click Board
The DIGI POT 4 Click Board is a digitally controlled dual potentiometer, with the resistance of 10KΩ. It has a 10bit resolution which allows for a very smooth linear wiper positioning through 1024 steps. Digital wiper position can be controlled via SPI interface. DIGI POT 4 click also features a non-volatile durable EEPROM memory for storing the wiper position, which means that the device can restore its last position after the power on - just like its mechanical counterpart.
Digi Pot 5 Click Board
The DIGI POT 5 Click Board is a digitally controlled quad potentiometer, with the resistance of 10KΩ. It has an 8bit wiper step resolution, which allows the wiper to take 257 different discrete positions (across 256 internal resistors). The digital wiper position can be controlled via the SPI interface. DIGI POT 5 click features a durable EEPROM non-volatile (NV) memory for storing the wiper position. The content of the wiper register memory located in the NV memory is copied to the actual wiper registers after the power-on or reset state, so the device acts similar to its mechanical counterpart, recalling its last used wiper position after being powered on. The device also features the WiperLock™ technology, which effectively locks the wiper position in place.
DIGI POT Click Board
The DIGI POT Click Board is a compact accessory board that incorporates a MCP4161 single-channel digital potentiometer. With a single resistor network, this digital POT features an 8-bit (256 wiper steps) resolution. DIGI POT click communicates with the target board microcontroller using industry standard SPI interface. DIGI POT click offers WiperLock Technology allows application-specific calibration settings to be secured in the EEPROM. The MCP4161 module is available with a resistor value of 10 k?
Digital Potentiometer Board
The Digital Potentiometer Board is an additional board that employs a MCP41010 single-channel, 8-bit digital potentiometer with 10k?
DIP to PLCC44 Adapter Board
Convert a DIP40 PIC socket into PLCC44 PIC compatible socket using the DIP to PLCC44 Adapter Board. Designed for a rapid and trouble-free operation, a PLCC (Plastic Leaded Chip Carrier) adapter allows the user to use a PIC with the PLCC housing shape in a device that supports only DIP packaging. The high-quality, compact-sized adapter board can be used with any programming board featuring the DIP40 socket. Without this adapter board, no connection can be established between the plug shape of a programming device and the housing shape of a chip. A PIC microcontroller is placed into the adapter before the programming starts. The microcontroller can be pulled out of the adapter after programming is done. DIP to PLCC44 Adapter Board supports a wide range of PIC microcontrollers, which includes 16F74, 16F77, 16F871, 16F874A, 16F877A, 18F242, 18F252, 18F442, 18F448, 18F452, and 18F458. DIP to PLCC44 Adapter Board is suitable for testing the PLCC44 chips. The top side of board fits socket while the bottom side of PCB features two single row surface mount vertical headers. It allows easy and fast work with PICs in PLCC44 package.