Click Blocker Tracking
The cookie settings on this website are adjusted to allow all cookies so that you have the very best experience. If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the account menu. 

The Debug Store - The Electronic Engineers' Tool Store

Mikroelektronika d.o.o.

Mikroelektronika d.o.o.

MicroElektronika (mikroE) is a dynamic forward thinking embedded systems development tools company with its headquarters in Belgrade.

MikroElekronika (MikroE) has chosen the Debug Store in the UK as their dedicated distributor of development tools.

The company is unique by producing complete development tool suites; ranging from compilers, debuggers, development platforms and training materials for a wide range of microcontroller families including ARM Cortex, AVR, PIC, PIC32, dsPIC and FT90x architectures. Support is also directly available for a huge range of peripheral devices including displays, video cameras, temperature probes and multi-axis gyroscopes and accelerometers by the provision of low-cost Click Modules. Their objective is to make the transition for the developer to a new architecture as simple and efficient as possible. It achieves this by providing software library support and working examples for all supported interfaces and development systems.

MikroElektronika (mikroE) have been chosen as the development tool company of choice by many major semiconductor manufacturers as they appreciate the use of mikroE tools will speed up development of new projects. They are recognised third-party development partners of companies such as Atmel, Cypress, Microchip, STMicroelectronics, Texas Instruments and official consultants to others including NXP.


Ozone 2 Click Board

The Ozone 2 Click Board is based on the Winsen MQ131 sensor for Ozone (O3). The sensor outputs an analogue voltage, which is converted by the on-board MCP3551 22-bit ADC converter or it is sent to the microcontroller via AN pin on the mikroBUS™, depending on the position of ADC SEL. jumper.

The click is designed to run on 5V power supply. It communicates with the target microcontroller over SPI interface or AN pin on the mikroBUS™ line.



Ozone Click Board

The Ozone Click Board carries a MiCS-2614 compact MOS sensor for ozone (O3) detection. Its detection range is from 10-1000ppb. An on board 12-bit ADC converts the analogue measurement to digital.

Ozone Click is a MikroBUSadd-on board with a MiCS-2614 compact MOS sensor for ozone (O3) detection. Its detection range is from 10-1000ppb. It's a small (5 x 7 x 1.55mm) MEMS sensor consisting of a micro machined diaphragm with an embedded heating resistor and the sensing layer on top.

The sensor outputs an analogue voltage, which is converted by the on board MCP3201 12-bit ADC converter.
Ozone click communicates with the target MCU through the MikroBUSSPI interface (CS, SCK, MISO). The board is designed to use a 5V power supply only.



PAC1921 Click Board

The PAC1921 Click Board is a versatile power monitoring and measuring device intended for the high speed, low latency measurements. This device can measure current, voltage or the power of the connected load. PAC1921 click features an integrated average power measurement, it can output the measured properties in the form of a filtered analog voltage level by using 10bit DAC, provides 1x to 128x current binary gain, it has an integrated second order input ADC, automatic zero offset, and all the measured values are available through the serial SMBus/I2C interface



PAC1934 Click Board

The PAC1934 Click Board carries the PAC1934 four channel DC power/energy monitor from Microchip. The click is designed to run on either 3.3V or 5V power supply.

It communicates with the target microcontroller over an I2C interface.



Pi 3 Click Board shield

By adding two mikroBUS™ sockets to your Raspberry Pi 3, the Pi 3 Click Shield allows you to experiment with hundreds of click boards™ from our ever expanding range. WiFi, Lora, Bluetooth, GSM, GPS, RFID, OLED, speech recognition, environmental sensors, movement sensors, biosensors, LEDs, relays, — you name it, we got it!

The Pi 3 Click Shield is compatible with Raspberry Pi 3 model B, 2 B, 1 A+ and B+.



Pi Click Board shield

The Raspberry Pi Click Shield is an extension for Raspberry Pi®, the low-cost mini-computer. It's a simple shield with a mikroBUS™ host socket to make your Raspberry Pi compatible with more than 360 different types of click™ boards.

The MikroBus connectors are soldered onto this board in the factory.



PI2 Click Board Shield

The Raspberry Pi 2 Click Shield is an extension for Raspberry Pi® models 2B and B+. It has two mikroBUS™ sockets that make it compatible with over 355 Click Boards.



PIC Clicker Board

PIC Clicker Board



PIC-Ready2 Board

PIC-Ready2 Board



PIC32MX Clicker Board

PIC32MX Clicker Board



PIC32MZ Clicker Board

The PIC32MZ Clicker Board is a compact development board with a mikroBUS™ socket for click board connectivity. It carries the PIC32MZ 32-bit microcontroller (1 MB Live-Update Flash and 512 KB SRAM) microcontroller with FPU from Microchip. To make your prototyping experience as convenient as possible, PIC32MZ clicker is preprogrammed with a USB-HID bootloader.



PICFlash Experimental Board

The PICFlash Experimental Board makes the process of programming MCUs easier. There are 8-, 10-, 14-, 18-, 28- and 40-pin DIP sockets provided on the board. There is also an on-board 40-pin ZIF Socket for easy handling of a microcontroller.