MicroElektronika (mikroE) is a dynamic forward thinking embedded systems development tools company with its headquarters in Belgrade.
The company is unique by producing complete development tool suites; ranging from compilers, debuggers, development platforms and training materials for a wide range of microcontroller families including ARM Cortex, AVR, PIC, PIC32, dsPIC and FT90x architectures. Support is also directly available for a huge range of peripheral devices including displays, video cameras, temperature probes and multi-axis gyroscopes and accelerometers by the provision of low-cost Click Modules. Their objective is to make the transition for the developer to a new architecture as simple and efficient as possible. It achieves this by providing software library support and working examples for all supported interfaces and development systems.
MikroElektronika (mikroE) have been chosen as the development tool company of choice by many major semiconductor manufacturers as they appreciate the use of mikroE tools will speed up development of new projects. They are recognised third-party development partners of companies such as Atmel, Cypress, Microchip, STMicroelectronics, Texas Instruments and official consultants to others including NXP.
GSM Antenna SMA straight male (Cable length: 2m)
GSM Antenna SMA straight male (Cable length: 2m)
GSM Click Board
The GSM Click Board is an ideal solution to add GSM/GPRS communication layer to your project. This accessory board includes a Telit GL865-QUAD GSM/GPRS module that supports GSM/GPRS 850/900/1800/1900 MHz Quad-band frequency. It also incorporates a TXB0106 6-bit bidirectional voltage-level translator and a SIM CARD socket (SIM card not included) integrated on the bottom side of the board. Ideal for mobile devices, GSM click make use of the seven mikroBUS lines (RX, TX, INT, PWM, CS, RST and AN) to communicate with the target microcontroller. The GSM click board comes with a SMA antenna connector as well as 3.5mm quadrupole earphone/microphone jack.The board can use either 3.3V or 5V power supply, selectable via SMD jumper. It is soldered in 3.3V position by default. It has an LED diode that denotes the status of power supply.
To extend the functionality of the board at no additional cost, GSM click has additional features such as integrated TCP/IP protocol stack (including UDP, SMTP, ICMP and FTP), serial multiplexer, remote AT commands and more.
GSM2 Click Board
The GSM2 Click Board from mikroE is introduced as a new and improved solution for adding GSM/GPRS communication layer to your design. One of the most popular click boards from MikroElektronika, GSM2 click is ideal for wireless mobile connectivity.
GSM2 click features the
GSM3 Click Board
The GSM3 Click Board from mikroE is the latest offering in the range of click boards with GSM modules. Intended to deepen user
GYRO Click Board
Introduce motion control to your design with the MikroElektronika
Hall Current Click Board
Hall current click is a measurement add-on board intended to measure the current utilizing the Hall Effect. The board features a high-precision galvanically isolated TLI4970-D050T4 magnetic digital current sensor in a tiny footprint. The Hall current click board is equipped with two EXTreme ZPower connectors (IP- and IP+) to connect a conducting wire. Split the conducting wire and connect the ends to the two connectors. The current rail is galvanically isolated from the interface to the microcontroller to keep the surrounding circuitry safe. The sensor detects the strength of the current, then sends the measurement data to the target MCU through mikroBUS SPI (SDO, SCK and CS) lines.
Hall current click is based on contact-free measurement principle, which causes no additional power loss and makes it perfectly suited for high efficiency systems. It is designed to use a 3.3V power supply only. The board is an ideal choice for photovoltaic and general purpose inverters, power supplies (SMPS), battery chargers, lighting applications, and electrical drives.
Haptic Click Board
Bring tactile feedback back to your hardware design with the Haptic click, featuring the DRV2605 IC, a driver for ERM (Eccentric Rotating Mass) and LRA (Linear Resonant Actuator) vibration motors. The DRV2605 module incorporates an extensive library with over 100 licensed haptic effects. These consist of audio-to-vibe feature, where the motor vibrates in tune with the lower frequency range of an audio input. A 3.5mm audio jack is also integrated into the board to use this functionality. The board also has screw terminals for secure connection to the ERM and LRA motors. Haptic click communicates with the target microcontroller using the mikroBUS I2C (SCL, SDA), EN (in place of CS) and PWM pins. It uses a 3.3V or 5V power supply. The extensive range of effects also implies that the resources of the host MCU aren
HDC1000 Click Board
The HDC1000 Click Board from mikroEis another humidity (and temperature) measurement solution that carries the TI
Heart Rate Click Board
Heart rate click is an accessory board that employs MAX30100, a pulse oximeter and heart rate monitor sensor. The Maxim