The cookie settings on this website are adjusted to allow all cookies so that you have the very best experience. If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the account menu. 
    
 

Sensors

Sensors

Products

6DOF IMU 2 Click Board

The 6DOF IMU 2 Click Board is a MikroBUSadd-on board with Bosch's BMI160 low power inertial measurement unit (IMU).

The BMI160 is capable of precise acceleration and angular rate (gyroscopic) measurement.

MIKROE-2337

£28.80

6DOF IMU Click Board

6DOF IMU click carries ST's LSM6DS33TR 6-axis inertial measurement unit comprising a 3-axis gyroscope and a 3-axis accelerometer.

MIKROE-1941

£28.80

AC Current Click Board

The AC Current cClick Board can measure alternating currents up to 30A. It features the MCP3201 ADC (analog to digital) converter and the MCP607 CMOS Op Amp, both from Microchip. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over an SPI interface, and the AN pin on the MikroBUSline.

AC Current click can only be used for sensors with voltage output (30A input current ,.

MIKROE-2523

£16.80

AC Current Click Board - bundle

With AC Current Clixck Board bundle (AC Current click + AC Current Sensor) you will be able to measure alternating currents up to 30A. The click board is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over an SPI interface, and the AN pin on the MikroBUSline.

MIKROE-2525

£34.80

Air Quality 2 Click Board

The Air Quality 2 Click Board carries the iAQ-Core Indoor Air Quality sensor that measures VOC levels and provides CO2 equivalent and TVOC equivalent predictions.

The click is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over I2C.

MIKROE-2529

£94.80

Air quality 3 Click Board

The Air quality 3 Click Board is the air quality measurement device, which is able to output both equivalent CO2 levels and total volatile organic compounds (TVOC) concentration in the indoor environment. The Click board is equipped with the state-of-the-art air quality sensor IC, which has an integrated MCU and a specially designed metal oxide (MOX) gas sensor microplate, allowing for high reliability, fast cycle times and a significant reduction in the power consumption, compared to other MOX sensor-based devices. The Click board is also equipped with a temperature compensating element, which allows for increased measurement accuracy.

MIKROE-2953

£34.80

Air Quality 4 Click Board

The Air Quality 4 Click Board is an advanced air quality sensing device that combines multiple metal-oxide sensing elements on a chip to provide detailed information of the air quality parameters. This click can output a TVOC value readings as well as the CO2 equivalent concentration readings in an indoor environment. Besides these compensated attributes, the click can also output raw values of H2 and Ethanol in the air, that can be used to calculate gas concentrations, relative to a reference concentration.

MIKROE-2896

£38.40

AIR QUALITY Click Board

The Air Quality Click Board features MQ-135 gas sensor in its design for measuring the air quality in apartments, homes and offices. This add-on board helps the users in detecting poisonous gases like ammonia (NH3), nitrogen oxides (NOx), benzene, CO2, smoke and others that harm the air quality, and pollute it. Air quality click is equipped with a calibration potentiometer and a power indicator LED. It also has got a MikroBUS host socket and two jumpers. The MQ-135 sensor features a gas sensing layer constructed of tin dioxide which is an inorganic compound with the formula SnO2. Tin dioxide is known to have lower conductivity in clean air.

As the level of pollution increases in the air, the conductivity rises too. User can calibrate Air quality click for the environment by adjusting the load resistance of the sensor circuit. As the concentration of the target air changes, the resistance of the sensor component also gets changed.

MIKROE-1630

£19.80

Alcohol 2 Click Board

The Alcohol 2 click is a very accurate ethanol gas (alcohol) sensor Click board™, equipped with the SPEC amperometric gas sensor which electrochemically reacts with the ethanol. It is supported by the LMP91000, a high-precision integrated analog front-end IC (AFE), perfectly suited for use in electrochemical sensing applications. The Click board™ also provides the reference voltage required by the sensor and offers a choice between the analog output from the AFE IC buffered with the low noise op-amp, and digital output from the 12-bit SAR A/D converter.

MIKROE-3097

£62.40

Alcohol 3 Click Board

Alcohol 3 click is a gas sensor Click board™, equipped with the MiCS-5524, a compact metal oxide (MOS) sensor. This sensor reacts to the presence of deoxidizing and reducing gases, such as ethanol (also known as alcohol). Its impedance changes as a result of a catalytic reaction, allowing it to be used in a voltage divider configuration. This voltage can be sampled by an accurate A/D converter (ADC), allowing data to be read directly over the I2C interface. The MiCS-5524 sensor itself is a robust sensor, which can be used in harsh environment for gas leakage detection, in breath checking applications, early fire detection, etc.

MIKROE-3318

£38.40

Alcohol Click Board

Add a high-sensitivity alcohol gas sensor to your design with the addition of Alcohol click. The board incorporates a MQ-3 high-sensitivity alcohol sensor to detect alcohol concentration. Made of an inorganic compound called Tin dioxide (SnO2), the gas sensing layer on the MQ-3 sensor unit has lower conductivity in clean air. However, the sensitivity rises as the levels of alcohol gas rise.

Alcohol click features a small potentiometer for calibration that enables the user to set its own scale and adjust the load resistance of the sensor circuit. Using the AN (OUT) MikroBUS line, Alcohol click communicates with the target board. This board is designed to use 5V power supply only.

It offers very good sensitivity and fast response to alcohol gases, and is designed to detect presence of alcohol in concentrations from 0.04 to 4mg/l. It makes an ideal choice for portable alcohol detector and breathalysers for estimating BAC (blood alcohol content).
.

MIKROE-1586

£18.00

Ambient 2 Click Board

The Ambient 2 Click Board carries TI??s OPT3001 Ambient Light sensor. It??s a small (2mm x 2mm) single-chip lux meter that measures only the visible part of the light spectrum from any kind of source (mimicking the way humans see light).

MIKROE-1903

£16.80