The cookie settings on this website are adjusted to allow all cookies so that you have the very best experience. If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the account menu. 
    
 

Serial Interface Click Boards

Serial Interface Click Boards


Products

1-Wire I2C Click Board

The 1-Wire I2C Click Board™ carries the DS28E17 1-Wire-to-I2C master bridge from Maxim Integrated. The Click Board™ runs on a 3.3V power supply.

It communicates with the target microcontroller over 1-Wire.

MIKROE-2750

£26.40

4-20 mA R Click Board

The 4-20mA R Click Board™ from MikroE is an accessory board that provides a simple solution to add 4-20mA industry standard communication protocol to your design. Offered in a compact package, this Click Board™ is intended to serve as a receiver in a 4-20mA current loop standard. It receives output current (4-20mA) from transmitter and changes it into a voltage ranging from 0.4V to 2V. The voltage is then converted into a 12-bit data signal in the MCP3201 Analog-to-Digital convertor.

It communicates with the target board microcontroller through MikroBUS SPI (SDO, SCK, CS) and EN lines. The 4-20mA R Click Board™ has a voltage output INA196 current shunt monitor, 12-bit resolution MCP3201 ADC and a high-frequency TPS61041 boost converter. It also features on-board screw terminal meant for easy connection. A complete 4-20mA current loop standard can be formed with the combination of this add-on receiver board with the 4-20mA T Click Board™.

Ideal for using in field of industrial process control and test systems, this 4-20mA Click Board™ works as an interface between sensors or instruments attached to microcontroller. It is designed to use either 3.3V or 5V power supply, selectable via SMD jumper (in 3.3V position by default). An LED indicates the presence of power supply.

MIKROE-1387

£31.20

4-20 mA T Click Board

The 4-20mA T Click Board™ from MikroE is an accessory board to provide an easy solution to add 4-to-20mA industry standard communication protocol to the user design. Offered in a small package, this Click Board™ is intended to serve as a transmitter in a 4-20mA current loop standard. It receives the input digital signal from the host microcontroller and sets the output loop current (4-20mA). The 4-20mA T Click Board™ has an ADuM1411 Quad-channel digital isolator, 12-bit single channel MCP4921 DAC and a XTR116 4-20mA current loop transmitter. It also features on-board screw terminal meant for easy connection. 4-20mA T Click Board™ communicates with the target board microcontroller through MikroBUS SPI (SDO, SCK, CS) and EN lines. A complete 4-20mA current loop standard can be formed with the combination of this add-on transmitter board with the 4-20mA R Click Board™.

It is designed to use either 3.3V or 5V power supply. An LED denotes the status of power supply.

Ideal for using in field of industrial process control and test systems, this 4-20mA Click Board™ functions as an interface between sensors or instruments attached to microcontroller. It is designed to use either 3.3V or 5V power supply. An LED denotes the status of power supply.

MIKROE-1296

£31.20

ATA6563 Click Board

The ATA6563 Click Board™ carries the ATA6563 high-speed CAN transceiver. The Click Board™ is designed to run on a 5V power supply. Use the VIO SEL jumper for selecting the 3.3V or 5V logic level.

It communicates with the target microcontroller over UART interface, with additional functionality provided by the AN pin on the MikroBUS line.

MIKROE-2334

£24.00

ATA6570 Click Board

The ATA6570 Click Board™ is a CAN Partial Networking interface board. The Click Board™ carries the ATA6570, a high-speed CAN transceiver that interfaces a Controller Area Network (CAN) protocol controller and the physical two-wire CAN bus. This IC has some unique features that make it a perfect choice for any embedded CAN application.

MIKROE-2900

£27.60

ATA663211 Click Board

The ATA663211 Click Board™ carries an Atmel LIN transceiver IC designed to handle low-speed data communication in vehicles and in industrial applications with electrically harsh environments. The LIN connection is established by attaching wires to the on-board screw terminals.

MIKROE-2335

£22.80

ATA663254 Click Board

The ATA663254 Click Board™ is a fully integrated LIN transceiver device with an integrated 5V LDO voltage regulator. The combination of voltage regulator and bus transceiver makes it possible to develop simple but powerful slave nodes in LIN bus systems. The integrated LDO can be used to provide power to the host MCU so that no additional voltage regulators are required, only the power supply connected to the LIN connector is needed. ATA663254 Click Board™ features the under-voltage protection, short-circuit protection, TXD time-out timer and its LIN physical layer complies with LIN 2.0, 2.1, 2.2, 2.2A and SAEJ2602-2 standard specifications.

MIKROE-2872

£19.20

CAN Isolator Click Board

The CAN Isolator Click Board™ provides isolated CAN communication. It carries the ADM3053 signal and power isolated CAN transceiver with an integrated isolated DC-to-DC converter.

The Click Board™ is designed to run on either 3.3V or 5V power supply. CAN Isolator Click Board™ communicates with the target microcontroller over UART interface.

MIKROE-2627

£46.80

CAN SPI Click Board 3.3V

The MikroE CAN SPI 3.3V Click Board™ is known to be the best accessory board designed to add CAN (Controller Area Network) connectivity to the microcontroller with SPI interface. The 3.3V version is exclusively designed for serial communication on 3.3V microcontrollers. The communication board features a high-speed SN65HVD230 CAN transceiver that serves as the interface between a CAN protocol controller and the physical bus. It provides a CAN serial communication physical layer in accordance with the ISO 11898 standard. CAN SPI Click Board™.

MIKROE-986

£25.20

CAN SPI Click Board 5V

The CAN SPI 5V Click Board™ is a highly reliable communication board intended to add serial CAN connectivity to user microcontroller with SPI interface. The 5V version is exclusively designed for communication on 5V microcontrollers. The accessory Click Board™ features MCP2551, high-speed CAN transceiver that serves as the interface between a CAN protocol controller and the physical bus. The CAN transceiver circuit provides a CAN serial communication physical layer in accordance with the ISO 11898 standard. The board has screw terminals to ensure easy and secure connectivity, power LED, and node termination jumper. It supports connection with up to 112 nodes. Designed to operate in especially-harsh environments, CAN SPI Click Board™ 5V provides cross-wire protection, loss-of-ground and over-voltage protection, over-temperature protection, as well as wide common-mode range. It uses a 5V power supply only.

CAN SPI Click Board™ 5V is an ideal choice for industrial automation, home automation, as well as in automotive and mobile machine industry.

Note: To add CAN SPI function to a 3.3V system, see the CAN SPI Click 3.3V board.

MIKROE-988

£25.20

ETH Click Board

Add Ethernet functionality to your project with the ETH Click Board™ from MikroE. This accessory board is provided with a 28-pin, 10BASE-T stand-alone Ethernet controller, ENC28J60 by Microchip. Compliant with all of the IEEE 802.3 specifications, ENC28J60 chip uses the industry standard Serial Peripheral Interface (SPI). The board also employs a Medium Access Controller (MAC) and Physical Layer (PHY) that provides additional functionality. ETH Click has an 8-Kbyte transmit/receive packet dual port SRAM with configurable transmit/receive buffer size. The board communicates with the host controller through an interrupt pin and the SPI communication lines with clock rates of up to 20 MHz. The ENC28J60 aboard ETH Click supports programmable automatic retransmit on collision as well as programmable automatic rejection of erroneous packet. ETH Click includes standard RJ-45 connector and LEDs for transmit, receive and power. The integrated crystal oscillator ensures stable operation. It is designed to operate with a 3.3V power supply only.

ETH Click Board™ is highly suitable for applications including VoIP, industrial automation, building automation, home control, security and instrumentation.

MIKROE-971

£28.80

ETH WIZ Click Board

ETH Wiz Click Board™ carries W5500, a 48-pin, 10/100 BASE-TX standalone ethernet controller with a hardwired TCP/IP Internet protocol offload engine, along with a standard RJ-45 connector.

MIKROE-1718

£22.80