The cookie settings on this website are adjusted to allow all cookies so that you have the very best experience. If you continue without changing your cookie settings, we'll assume that you are happy to receive all cookies on our website. However, if you would like to, you can change your settings at any time using the Change cookie settings link in the account menu. 
    
 

Temperature Sensors

Temperature Sensors


Products

DHT22 2 Click Board

The DHT22 2 Click Board is used for measuring the environmental temperature and relative humidity. It uses the CM2322 sensor, with very accurate thermal and humidity measuring capabilities. It can use either 1-Wire or I2C protocol to communicate with the integrated circuit.

Attributes like the ultra-small size, low power consumption, signal transmission distance up to 20 meters, make this sensor the perfect choice for all kinds of applications that require measurement of the temperature and humidity.

MIKROE-2818

£26.40

DHT22 Click Board

The DHT22 Click Board from Mikroelektronika is one of the simplest temperature and relative humidity sensor click board that carries the AM2302 sensor module, also known as DHT22. Concealed inside a plastic mesh packaging, the AM2302 temperature/humidity sensor needs just a single wire to communicate with the target board microcontroller.

For added convenience, DHT22 click is provided with two jumpers (zero ohm resistors). While one of them allows the user to choose between the MikroBUS pin to use (either CS or INT pin, which are SDA1 and SDA2 lines), the other on-board jumper allows the choice between 3.3V and 5V power supplies. The sensor generates the temperature/humidity data in a 16-bit resolution. The generated decimal number is 10 times the actual measurement, i.e., 216 would be 21.6.

MIKROE-1798

£28.80

Fan 2 Click Board

The Fan 2 Click Board carries the MAX31760 precision fan-speed controller. It can measure temperature and adjust the fan speed to keep the temperature at the same level. Fan 2 click can also control two fans at the same time.

The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over I2C interface, with additional functionality provided by the following pins on the MikroBUSline: INT, AN, RST, CS.

MIKROE-2708

£18.00

Fan 3 Click Board

The Fan 3 Click Board is the perfect choice for speed control and it can operate in seven discrete speed steps. Unlike the PWM regulation which can sometimes cause the infamous coil whining effect on some types of fans, this click board outputs the selected voltage via the MIC29152 voltage regulator from Microchip, driven through the MIC74 - a serial to parallel I/O expander and a fan controller from the same company, keeping it constant at the output. Fan 3 click works with 12V to 25V on its input connector and can be used whenever a noiseless solution with a variable fan speed is needed, for example - cooling of electronic components with the minimal possible noise produced.

MIKROE-2841

£21.48

Fan 4 Click Board

Fan 4 click is a very compact, two-wire fan driver. It utilizes an integrated 5V, DC, brushless-motor driver chip. Its output voltage regulation and current limiting capabilities allow the speed control for the two-wire DC brushless motors. The Click board uses the LTC1695 IC, which features an integrated 6-bit DAC. The DAC regulates the output voltage in the range from 0 to 4.92V. This IC also has some additional features, such as the maximum output current limiting, and thermal shutdown protection. There is also a startup boost timer which ensures reliable startup of the fan, connected to the output terminal.

MIKROE-3200

£18.00

Fan Click Board

The Fan Click Board carries an EMC2301 controller for powering and regulating the operation of 5V four-wire fans, which are commonly utilized as coolers in computers and other electronics.


.

MIKROE-2004

£11.88

SHT Click Board

The SHT Click Board is a temperature and humidity sensing click board that carries Sensiron??s SHT3x-DIS IC. Compared to its predecessor (SHT11), SHT3x click has increased reliability and enhanced signal processing features with a high signal-to-noise ratio.

MIKROE-2101

£31.20

Storm Chaser's Click Board Pack

Storm Chaser's Click Pack.

MIKROE-1639

£90.92

Temp&Hum 10 Click Board

Temp&Hum 10 Click is a smart temperature and humidity sensing Click board, aimed towards IoT applications, due to its extremely small size and very low power consumption. It can measure a wide range of temperature and relative humidity (RH) values with high accuracy. The sensor used on this Click board offers the complete measurement system: capacitive RH sensor, thermal sensor, analog and digital data processing, and the I2C communication interface. Featuring a good reliability over time, high accuracy, and low hysteresis, it is an ideal solution to be used in various temperature and humidity related IoT applications.

Temp&Hum 10 click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click board comes as a fully tested product, ready to be used on a system equipped with the mikroBUS socket.

MIKROE-3342

£19.20

Temp&Hum 2 Click Board

Temp&Hum 2 click is a smart temperature and humidity sensor click board, packed with features, that allow easy and simple integration into any design that requires accurate and reliable humidity and temperature measurements. It measures a wide range of temperature and relative humidity values with a great accuracy. The Si7034 sensor IC from Silicon labs used on this Click board utilizes the patented industry-standard low-K polymeric dielectrics for humidity sensing. It allows low drift and, power consumption, low hysteresis, and excellent long-term stability.

MIKROE-3085

£19.20

Temp&Hum 3 Click Board

The Temp-Hum 3 Click Board is a smart environmental temperature and humidity sensor Click board, packed with features which allow easy and simple integration into any design that requires accurate and reliable humidity and temperature measurements. The sensor IC has integrated sensing elements placed on the bottom of the die, so they are not directly exposed to the environmental contamination. This translates to a prolonged life of the Click board itself.

MIKROE-2937

£15.60

Temp&Hum 4 Click Board

Temp&Hum 4 click is a smart environmental temperature and humidity sensor Click board, packed with features which allow easy and simple integration into any design that requires accurate and reliable humidity and temperature measurements. The sensor IC itself has integrated sensing elements placed on the bottom of the die, so they are not directly exposed to the environmental contamination, which translates to a prolonged life of the Click board.

MIKROE-2938

£15.60